CDM2000RW429 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- edward from early branch, SC
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clip on door broke
it was easy, it clip right on.needed to give it a little tap to get it in .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Roswell, GA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stripped knob on dryer
ordered replacement. received in two days and voila! Fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Hawley, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob pastic insides broke
pulled off the old knob and replaced it with the new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Austin, TX
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken "start" knob
The start knob had crack in it that was getting bigger, and we'd begun using pliers to start it. Not only was it unwieldy but I thought it would eventually strip the metal stem. Of course this was a breeze of a repair--we just slid the new knob on. But my husband had been certain that finding a replacement knob--or calling a dealing and ordering the part--would be a big deal. I said: "But let's just try on-line." We quickly found the model # inside the dryer door. We filled in the appliance info, the part popped up. I ordered it. It arrived in 2 days. It's like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- susan from Cypress, TX
- Parts Used:
- WE25M40
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
It was making a loud noise
First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from San Diego, CA
- Parts Used:
- WE25M40
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Squeaky dryer
First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.
I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.
I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.
I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.
I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Greenville, IL
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
loud squeeking noise when dryer was runnig
nd removed it from the unit.
5. replaced drum bearings
6. reassembled everything in the same order I took it off.
Be sure to mark any wires you may disconnect to ensure you connect them back correctly.
Was a bit frustrating at times, but made it through and there is no more squeek.
5. replaced drum bearings
6. reassembled everything in the same order I took it off.
Be sure to mark any wires you may disconnect to ensure you connect them back correctly.
Was a bit frustrating at times, but made it through and there is no more squeek.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from scottsdale, AZ
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob Broken
The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Redondo Beach, CA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not stay closed
inserted the latch into the opening in the front face of the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Upper Marlboro, MD
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer selector knob
I opened the box which contained the new selector knob. Placed it on my dryer and immediately turned the knob to start the dryer. Easy steps to follow the video supplied when i ordered the part. I am greatful you responded to my order within 3 days. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Mercerville, NJ
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastics broke on inside of "Start" knob
Pushed new knob on starter shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from POPLAR GROVE, AR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
selector knob was striped out
Just took the old knob off and put the new knob on. It was a snap. Thanks you very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bradley from noble, OK
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
on/off knob cracked and would not turn on the dryer
put the new knob on and pushed it inward !! simple repair..PartSelect is a great company to do business with and very quick shipping, and great prices too. thank you so much.Brad S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orange, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Simple replacement. Very easy.
Was this instruction helpful to you?
Thank you for voting!