62190429 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- mitchell from Warren, NJ
- Parts Used:
- WE25M40, WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
sqeekysqueeky rear drum bearing
Open top by removing 4 phillips head screws above opened door, pop top up. Remove rear access panel, remove belt from drive & tension pully. Loosen top front screws, remove front panel to gain access to remove drum. After drum removed, I realized why rear bearing went bad- two front guides were worn causing rear bearing to angle and wear out. Replaced front pads, buttoned her up and now quite as new. Also replaced drive belt while in there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PRESTON from CINCINNATI, OH
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Drum Would Not Turn
Remove the bottom cover of dryer to look at the motor, see belt hanging remove broken belt. Remove screws from the top and front, slide belt over drum put small piece of tape to hole belt in place replace screws go back to the rear pull belt over the motor pulley close back panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from OLD TOWN, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher
Replace both micro switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Williamston, MI
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Belt Broken that turns the drum
First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from CRAWFORDVILLE, FL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
knob broke
Just pushed on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Westminster, MD
- Parts Used:
- WE25M40, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
clothes being eaten first then the loud noise
I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TAMPA, FL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The small clip in the Timer Knob was broken and the Knob would not turn the timer.
First I took the system apart which I did not have to do. However, by doing that I was able to figure out which parts make the timer run. Anyhow, you simply place the new timer knob on the small shaft and it worked like magic. It was very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from LIMA, OH
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Put the knob on and turned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BIRMINGHAM, AL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Timer knob stop working
Just took off old one installed new one. It came right on. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LEONARDTOWN, MD
- Parts Used:
- WE1M652
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob fell off. Had a crack in it.
Opened the package. pushes the new knob on and voila it worked! It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christel from GREENACRES, FL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The timer knob was inoperable
Very simple: I looked up the part number for my timer knob, ordered it from this site and received it one day earlier than expected. I simply attached the knob, and my problem was over. I am very, very satisfied and happy with your immediate delivery of the ordered part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from ALLEN PARK, MI
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knob broke and ordered a new one
Very easy fix since it was only the knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CAROLINE from SAN ANTONIO, TX
- Parts Used:
- WE1M652
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Very simple. Ordered the part. Received correct part and fit perfectly.
Was this instruction helpful to you?
Thank you for voting!