GHDP490GF2WW General Electric Dryer - Instructions

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....

Shortly after a piece of felt (the duct felt seal) was visible on the drum intererior, the dryer started making metal-on-metal squeaks. A few weeks later it started leaving'machine part' type brown/black marks on clothes. With the model # it was quite easy to find and order the correct part, which arrived a few days later. The accompanying video made installation quite straightforward, even for someone who's NEVER worked on a dryer before - even though the model used wasn't the same. Over half the repair time was to clean out lint and dirt from the various exposed parts. Overall, an easy and effective repair that solved the staining issue. Follow the video and you won't go wrong.

Be sure to segregate and label all screws.
Remove back and front of control panel.
Removed dryer top.
Removed dryer front/door panel.
Replaced slides. Due to discoloration it was hard to tell the white fr the green. Double checked partselect videos to be sure which was which.
Propped up drum with the dowel to allow enough room to access the coils. One of the screws was frozen. Soaked in penetrating oil for 30 minutes. Then used a Philips headed socket to break it free. Used needle nose pliers to lift out old coils and to place new coils.
Reversed process to reinstall all panels.
Crossed fingers and tested. AOK.

This was so easy. I used needle nose pliers to reach in and remove the metal clip which had slipped off of the inside of the knob and was on the post the knob was supposed to attach to. Next, I lined up the flat side of the "D" of the inside of the knob to the flat side of the "D" on the post and pushed it in until it snapped into place, and I was done. The dryer now works like new.

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.

I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!

inserted the lint catcher into the opening to replace the old one

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

I removed several torx srews across the back control panel. Removed two philips screws under top of front dryer door. Pulled up on top surface of dryer case. Removed two more screws on backside of front door panel. Pulled front door panel forward and inserted drum slides into slots that they just popped into with a small button rod to keep them in place. The old drum slides were completely worn down or fell off. It runs like a new one again. It is over 10 years old.
The new door handle just snapped into place.
Original door handle had been broken off for several years.

Very easy. Just take each wire from old switch and transfer to new.

Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.

Did repair as per the video except I did not disconnect wires, just swung front panel around. Only complaint...discovered parts were much more expensive than other sites.

had a great video to follow, made it easy to install.