Models > GHDP490GF1WW > Instructions

GHDP490GF1WW General Electric Dryer - Instructions

Jump to:

All Instructions for the GHDP490GF1WW
121 - 135 of 404
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Carole from Wynnewood, PA
Parts Used:
WE05X20431
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bulb dead
remove the old one and put the new one...!!! Easy
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
syd from wilmington, NC
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
no handle
just replaced the unit handle and how my wife can open the dryer without a screwdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clarke from Grapevine, TX
Parts Used:
WE03X37317
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Loud squeek when dryer was running
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Al from CORP CHRISTI, TX
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff D from NEW MEADOWS, ID
Parts Used:
WE03X29897
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dorothy from LACYGNE, KS
Parts Used:
WE01X20378
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
knobs cracked
Push on. But one pushed in panel
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anna from LELAND, NC
Parts Used:
WE01X20378
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
The dryer would not turn on.
We took the knob off of the machine and it appeared to be cracked on the inside. We ordered a new one and received it in 2 days. We matched the inside of the new knob to the stem coming out of the machine and placed the knob on the stem. The machine was fixed and we were happy! Thanks Part Select.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from ALLEN PARK, MI
Parts Used:
WE4M527
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
4Temp timer hard to rotate
Replaced with new part. Moved wiring one lead at a time as per instructions
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cheryl from WILDER, KY
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Door handle broke
Called my son-in-law. Easy as pie
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from BALTIMORE, MD
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Loud squeaking
Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from HARTSVILLE, TN
Parts Used:
WE4M527
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Timer stopped turning
Unplugged the old wire and connected new one at a time placed new timer back in position. Screwed cover back on and started drying clothes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Laurel Springs, NJ
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minutes or less.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Darryl from FARR WEST, UT
Parts Used:
WE17X22217
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phuc from WOODBRIDGE, VA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from EPHRATA, PA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GHDP490GF1WW
121 - 135 of 404