DG09-US0 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MonaLisa from Bronx, NY
- Parts Used:
- WE18X25100, WE14X25080
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Horrible screeching noise when the dryer drum was in motion, cracked pieces were tangling and ripping the drying clothes.
I removed the top of the dryer (unscrewed from the inside to release the top). Removed interior screws to pull open the front of the dryer. Once inside, it was really visible that the old parts (front air duct top and bottom) were in bad shape. They were cracked and broken. I removed the old pieces (they pretty much cracked and crumbled right off). I snapped in the new pieces careful to avoid damaging the electrical connections and wires. Once snapped into place (top and bottom), I careful put the front back into place making sure that the dryer drum rested on the new pieces. All screws back in place and all done! Dryer is now working as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Hedgesville, WV
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer developed a progressively noisy squeak over several months
I followed the directions that were listed on this site by other Do It Yourself individuals...by the way I'm a lady and more mechanically inclined than my husband, but he was a great help in lifting the drum up and out. (I unplugged the dryer before starting repairs)
1. I removed the two screws located at the top of the dryer inside the door.
2. Top of dryer cabinet lifted up after screws were removed.
3. Located and removed front panel retension screws and removed front panel and set aside
4. slipped belt off motor by reducing tension on idler pully
5. Removed screws inside drum that secured drum to bearing assembly
6. Husband and I lifted drum up and out of cabinet (this went very smoothly and took less than 15 minutes time.
7. Followed supplied bearing drum instructions and removed old bearing and installed new assembly.
8. Thoroughly cleaned out internal cabinet, blower, and motor areas
9. Reset the idler pully into proper position.
10. Tipped dryer on 'back' to reseat the drum With A NEW DRYER BELT (taped temporarily around the drum) into the bearing shaft (I may not be using the proper terms)
11. tipped dryer upright and while Hubby balanced the drum, the front panel was resecured to the rest of the cabinet.
12. Removed temporarily applied tape that held the drum belt in the general position, then using the rear access panel, I slipped the belt over the motor into the proper posisiton.
13. Top cabinet was reapplied and screwed into
place.
14 Plugged in and tested the dryer...NO SQUEAKS and it works beautifully and quietly!!
The job is not terribly difficult, but I am only 5 feet tall and the drum is bulky to work with and balance. Reaching into the cabinet to slip the belt onto the motor stretched my arm to the limit.
I found the cabinet reassembly and realignment of the screw holes quite annoying. But the total job proved satisfying upon completion.
1. I removed the two screws located at the top of the dryer inside the door.
2. Top of dryer cabinet lifted up after screws were removed.
3. Located and removed front panel retension screws and removed front panel and set aside
4. slipped belt off motor by reducing tension on idler pully
5. Removed screws inside drum that secured drum to bearing assembly
6. Husband and I lifted drum up and out of cabinet (this went very smoothly and took less than 15 minutes time.
7. Followed supplied bearing drum instructions and removed old bearing and installed new assembly.
8. Thoroughly cleaned out internal cabinet, blower, and motor areas
9. Reset the idler pully into proper position.
10. Tipped dryer on 'back' to reseat the drum With A NEW DRYER BELT (taped temporarily around the drum) into the bearing shaft (I may not be using the proper terms)
11. tipped dryer upright and while Hubby balanced the drum, the front panel was resecured to the rest of the cabinet.
12. Removed temporarily applied tape that held the drum belt in the general position, then using the rear access panel, I slipped the belt over the motor into the proper posisiton.
13. Top cabinet was reapplied and screwed into
place.
14 Plugged in and tested the dryer...NO SQUEAKS and it works beautifully and quietly!!
The job is not terribly difficult, but I am only 5 feet tall and the drum is bulky to work with and balance. Reaching into the cabinet to slip the belt onto the motor stretched my arm to the limit.
I found the cabinet reassembly and realignment of the screw holes quite annoying. But the total job proved satisfying upon completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kate from MULLINS, SC
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door latch was broken
Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennie from Louisville, GA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broken
Inserted handle into slots
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Eagar, AZ
- Parts Used:
- WE05X20431, WE16M15
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Blower wheel shaft hole was rounded out, lamp was out
Removed two screws on dryer top and removed top, removed two screws holding front of cabinet and removed cabinet front to the side, disconnected wires to door switch, removed two bolts from motor mount bracket, pulled motor back to access blower wheel, removed old wheel and installed new one, reversed steps, unscrewed old light bulb and screwed in new one.
Had pure hell getting to drum belt and putting it back onto motor pulley and idler, cussed a little, didn't really help . replaced front of cabinet and top, did test run all worked ok.
This job was a little difficult, espicially accessing the belt and idler pulley...
Had pure hell getting to drum belt and putting it back onto motor pulley and idler, cussed a little, didn't really help . replaced front of cabinet and top, did test run all worked ok.
This job was a little difficult, espicially accessing the belt and idler pulley...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from simi valley, CA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
new lint filter
my problem was easy, i orderd a new lint filter, for a
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Windber, PA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door wouldn't stay shut
When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from Newfield, NJ
- Parts Used:
- WE4M216
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer wouldn't heat up
I wanted to fix the cheapest possible problem first which was the thermostat.
Got the dryer apart and it was the wrong thermostat for the dryer, which was good news! I looked in inside floor of the dryer cabinet and saw alot of tiny "springs". Couldn't figure how they got there.
Turned out they were coils from the heating element. Must have burnt out and fell free from the element. So I ordered that and replaced it.
I want to say that I'm in NJ and I ordered that thermostat and got it in ONE DAY! Thought that was too good to be true but when I ordered the heating element THAT CAME IN ONE DAY!
I don't know what kind of people work in the shipping department but they are awesome! You really made the difference on this job.
So did the info on your website. I've never even seen a dryer apart before. It was a piece of cake thanks to you guys. You just saved me about $500.
Got the dryer apart and it was the wrong thermostat for the dryer, which was good news! I looked in inside floor of the dryer cabinet and saw alot of tiny "springs". Couldn't figure how they got there.
Turned out they were coils from the heating element. Must have burnt out and fell free from the element. So I ordered that and replaced it.
I want to say that I'm in NJ and I ordered that thermostat and got it in ONE DAY! Thought that was too good to be true but when I ordered the heating element THAT CAME IN ONE DAY!
I don't know what kind of people work in the shipping department but they are awesome! You really made the difference on this job.
So did the info on your website. I've never even seen a dryer apart before. It was a piece of cake thanks to you guys. You just saved me about $500.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Washington, PA
- Parts Used:
- WE4M325
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer not heating. When moving it away from wall it was sparking badly where the cord hooks up.
Removed case parts to expose internal wiring. Vacuumed up various types of mouse debris and plugged hole they were using. Ordered terminal block to replace the one that melted while sparks were flying. Replaced power cord with one I had in my basement from some other appliance that died a while ago. "Hey honey, ya know those old parts I saved..." :) Now it is heating to capacity and no spark-show! Oh yeah, the part I ordered from Partselect.com was delivered to my door the next day!!!!! Wow!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Mindoro, WI
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic door handle on the dryer broke and came off.
I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Laguna Niguel, CA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The belt borke after 10 years of use.
1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Laguna Niguel, CA
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer Making Scraping Noise - Front Side
Read the other posts - they are very good. On my particular dryer it took two Slide WH and two Slide Dryer Drum Side PS266785.
Most time spent was vaccuming out and removing a softball size ball of lint clogging the dryer - now it will actually dry clothes!
Part select delivery is really fantastic (even though it took me three orders to get it right!).
Most time spent was vaccuming out and removing a softball size ball of lint clogging the dryer - now it will actually dry clothes!
Part select delivery is really fantastic (even though it took me three orders to get it right!).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Downingtown, PA
- Parts Used:
- WE3M26, WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Terrible screech/chirping sound from Dryer
I followed the instruction of the first posting for this category and it worked perfectly...thanks for the nice detail...
- Upon receipt from PartSelect, placed new slides in Drum Bearing (this does not come together or as a kit - must order 4 slides AND Bearing separately for this dryer model)
- Loosened Top panel screws (2) from inside door area
- Slid top of dryer off - PAY attention to HOW the top comes out (tabs at the back and slots on the sides) or replacing the top could prove frustrating)
- Loosened Front panel screws (2) and GENTLY leaned the panel forward to access Drum Bearing - no need to REMOVE the front panel but be aware of the switch wires when leaning and the weight of the door if you did not remove that
- Removed old Drum Bearing
- Vacuumend interior of dryer cabinet (especially area leading down to vent)
- Snapped new Drum Bearing into place
- Re-secured Front panel paying attention to drum position to make sure everything still rotated properly and freely
- Reset Top panel - align back tabs first, gently pull forward just a bit until Top slips down over side tabs, then slide back into place and re-secure
Worked like a charm - took about 20 minutes...
- Upon receipt from PartSelect, placed new slides in Drum Bearing (this does not come together or as a kit - must order 4 slides AND Bearing separately for this dryer model)
- Loosened Top panel screws (2) from inside door area
- Slid top of dryer off - PAY attention to HOW the top comes out (tabs at the back and slots on the sides) or replacing the top could prove frustrating)
- Loosened Front panel screws (2) and GENTLY leaned the panel forward to access Drum Bearing - no need to REMOVE the front panel but be aware of the switch wires when leaning and the weight of the door if you did not remove that
- Removed old Drum Bearing
- Vacuumend interior of dryer cabinet (especially area leading down to vent)
- Snapped new Drum Bearing into place
- Re-secured Front panel paying attention to drum position to make sure everything still rotated properly and freely
- Reset Top panel - align back tabs first, gently pull forward just a bit until Top slips down over side tabs, then slide back into place and re-secure
Worked like a charm - took about 20 minutes...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bill from clarendon hills, IL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter was broken
took out broken filter and replaced with new lint
filter.
filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from Needville, TX
- Parts Used:
- WE3M26, WE03X37317, WE1M462, WE1M461, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
Unplugged dry cord . Removed top and front cover. Removed drum to replace rear Bearing. Reinstalled drum replaced front bearings and sleeve. Reinstalled both covers and plugged in.
Was this instruction helpful to you?
Thank you for voting!