PTMN945GMGG0 General Electric Dryer - Instructions

I read the repairs that others had posted and how they did it. It was really easy. My only complaint is that I didn't know that I needed the slides that attached to the bearing and couldn't find them on the repair list. My dryer had a spot for 4 of them and only 1 was left. Otherwise, being a female, I felt great to be able to fix it myself! Thanks!
Let me also say, I only have one good working arm/hand.

Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.

The bracket on the part supplied was different than the original. The wire connector was also different. The bracket had to be drilled for a hole to match the original. The connector had to be cut off and the wires soldered together, then tied off to the frame to keep them away from the flame. The repair works like new but not the simple plug and play I was expecting. In all fairness the exact model number was not available, probably since the appliance was 24 years old, so I chose the closest model number with the picture that looked like what I had. Problem solved.

I followed the instructional video that was given online. The parts fit well, and was easy to repair.

I followed the video instructions provided to me by this site

remove to screws in front to take of top. Then remove two screws holding the face on. change parts re assebmle. extra hands nice for holding drum while remounting face. Nice and quiet now.

Remove the old bearing assembly and Replaced with the new bearing assembly with new bearing slides.

Exactly how your perfect video instructions showed me. Thank you for a job well done!

I followed the directions I found on my tablet on youtube.

Follow the instructions from YOUTUBE to replace the new drive belt..

Dryer started making screeching noises while running, got progressively worse. Without taking it apart first, I ordered a front drum bearing and slides because this site said it fixed the problem the majority of the time. The site said replace the slides in pairs, but there are actually four. I picked up 2 more at a local appliance store, at roughly twice the price. Turned out I didn't need th replace the plastic piece called drum bearing, just the 4 slides that clip onto it. It is really easy to get the top and front off with just a phillips screwdriver. I did not check the rear center main bearing, as it requred removing the drum. The squealing lessended but it still was bad. Took it back apart and pulled the drum, and fount the rear main bearing bad. I found one at the same local store for only 2 bucks more than on this site. This was a bit more of a hassle, you really need two people to get it mounted to the drum. Tip-pre thread the holes with the self tapping screws, it makes it easier to get it together. There was a bit of lint build up under the drum heating element cover, so it was good to clean that out. Also blew all the dirt out of the motor with compressed air and shop vac. There was a access panel on back to get to the motor and belt tensioner. Got the dryer all buttoned up and now it runs nice and quiet.

removed top, 2ea screws ;removed front door,2 screws; removed left side panel,screws on bottom and back; removed belt,pulled out drum. replaced top drum bearing,installed green and white slides,re assembled w/ new belt,ops. check ok.

Replacing the front slides is easy. Just buy the parts and pop them in. The rear drum bearing is also easy, and you do not have to spend $50. Once I had the parts in hand, which is an axle from the rear of the drum and a bearing sleeve from the rear of the dryer cabinet, it looked quite simple and it is. I went to a hardward store, bought a bronze bearing that fit the axle and the sleeve and a C-clip. Cut the bearing to the correct length with a pipe cutter, and retain over the axle with the clip. Grease it up, and put the dryer back together. Total cost, $5. It works great.

loosened two hose clamps and four screws to replace the anti siphon valve.

The dryer was very noisy when it would start. The drum had warn the pads out and the drum was riding on the drum bearing. It really isn't a bearing more of a big piece of plastic. On the bearing are 4 slides (2 white and 2 green). These are easy to replace if the bearing is good. I let mine go too long and wore part of the bearing off. To fix: UNPLUG! Open the door and find 2 screws facing upward screwed into the top. Remove these 2 screws and remove the top. Take notice of how it comes out of the dash. On each side of the front panel (from inside) there is a smaller screw with a bigger head, remove both of these. You can now lift the front panel away from the drum and pull the front panel right out. It would be a good time to take a shop vac and clean all the lint out of this. Mine was almost full. If you are changing the bearing it is held in place with clips built on the bearing. Remove and replace. Put on the new slides as well. There is a little tab on the bearing and a hole in the slide. put the hole over the tab. The green ones I put on the top and the whites on the outter sides. Put the bottom of the panel in first and line up the drum on the new bearing, replace the 2 big headed screws, line up the top in the dash and lower into position, replace the 2 screws up inside the door and you are done. I have no dryer experience and would rate this job on a scale of 1-10 to about a 3 or a 4. There were no real suprizes.