GTMP520GD5WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- AMY from RICHMOND, VA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broke off
Very satisfied. I simply took the plastic door handle out of the package and snapped it into the door. It popped right in and fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Houghton Lake, MI
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door handle
just snap in replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Redlands, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke off
Just popped the new door handle on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Dublin, OH
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The handle on the dryer broke off
I ordered the new part as listed and it came in two days, which was amazing to me since it was the week before Christmas. I snapped it in in less than a minute and all is well. Thank you for being so prompt on sending this out. Made the holidays a lot easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce R from Boca Raton, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Clipped on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Joliet, IL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pull door handle broke
No tools needed as old handle had come out on it's own when it broke. Simply removed duct tape that was used holding old one in place till new one arrived. Placed new one in position and snapped into place to hold. Less then a minute to install. Very pleased and surprised in how fast delivery of part from PartSelect was. Basically had it in 2 days. Will use them for other replacement parts as the need arises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from flushing, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door handle to dryer broke...got part in 2 days,took 2 seconds to fix.
just 4 slots where the handle goes. Snapped handle into slots, good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Hilton Head, SC
- Parts Used:
- WE49X22295, WE20X20417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inside of door rusted
Very simple...just remove the inside of the door & replace.Great service on delivery of item ordered.quick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hilliard, FL
- Parts Used:
- WE14M104
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
burner assy rusted out at corners,spitting sound when on.
1. turn off gas.2. disconnect electric.3.Remove 3/8 gas line from rear of burner. 4.disconnect two electric connectors from gas valve assembly. 5.disconnect electric line from igniter. 6.remove two mounting sheet metal screws from front of gas valve assembly(5/16 socket). There also may be a screw holding assembly to the bottom plate.7. remove entire assembly from dryer by pulling out to the front. 8.remove igniter assembly and replace on new burner. 9. two sheet metal screws 1/4 inch hold burner assembly to gas valve assembly.10.Install in reverse order . it may take a few seconds for the gas to get down to the burner. don't forget to change over the air mix valve to the same place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Summerdale, PA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would run for 4 minutes and shut off. keep turning it on
Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Cumming, GA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Parkersburg, WV
- Parts Used:
- WE4X448
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer wouldnt stay heated
Took off the top cover then took off the front panel and installed the new coils on gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Newport, AL
- Parts Used:
- WE49X22295
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Rusty door
Removing the old door was the problem as the old screws were rusty. Then, because we are not very spatially adept, we had trouble putting the door back together with correct hinge alignment. This should have taken about an hour and the part was perfect. The dryer, which we were going to throw away, looks and works perfectly! Parts Select offers great, timely service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Richmond, VA
- Parts Used:
- WE4M415
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer would not turn on
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phillip from denver, CO
- Parts Used:
- WE01X20419
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
none
Snap in place
Was this instruction helpful to you?
Thank you for voting!