D537E*129 General Electric Dryer - Instructions

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

place inside of dryer

I just replaced the old filter with the new filter and I wonder why I didn't order a replacement filter sooner.

Found and ordered igniter on Tuesday. Part arrived on Friday. Took about 5 minutes to remove old igniter and install new one. Took about 5 minutes. Dryer works like new again. Hopefully it will last for another 16 years!

I called customer Servioce and they helped me with the corrfect part number

Pulled the old filter out of the door of the dryer and then removed the new filter from the shipping box and took the new Lint filter out of the packaging and then slipped the new lint filter into the lint filter holder and started up the dryer and away we went on our happy way. Thanks to all of you guys and gals at PARTS SELECT.

Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1

I looked on the internet for instructions to take the dryer apart,took the parts out one at a time ,and replaced them.It was easy and it made the dryer quiet again.I could see the obvious wear on the parts.I was happy to save the money a new dryer would cost.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Removed the screws that hold the draying unit (barrel) to get accest to the back of the switch, and that's when I noticed that I will need the belt and I ordered to when my existing belt goes I have a replacement.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

Followed an online website, removed the top, front, two rear access panels, disassembled the spring clip from the rear of the drum, took the belt off of the motor, removed the drum, took the rear bearing support out, replaced the bearing and reassembled the dryer.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Started with removal of rear inspection plate on rear of drier,rotated drier drum by hand to look for any visible problems. Found that drive belt with age had lost sections of teeth and every time the bad sections would go past motor they would "thump".
1. Removed belt from tensioner. Done simply by moving tensioner to unload belt.
2. Slipped belt off motor drive and moved belt to front of drum.
3. Opened drier door and removed 4 screws from under the lid or top of drier ,raised lid for access to belt once belt had been slid to front of drum.
4. (steps 4 and 5 are the hardest parts)Worked drive belt between drum and felt insulators keep in mind there are many stamped steel pieces and sharp edges can be present.
5. Removed belt by feeding a small section past felt and drum and worked rest out from frt. top of drier.
6. Installed new belt in reverse order as removal.
This was done without aid of instruction manual and by someone having major back surgery 4 months earlier. No idea how much this saved me but the price of the belt and time and effort involved made it woth my while I'm sure.

The part received had about 6" of the screen not bonded to the frame. I used clear epoxy and a 1/8" dia. dowel wrapped in saran wrap. after applying the epoxy to the screen/frame interface, the wrapped dowel was clamped to the frame. After the epoxy cured I removed the fixture and peeled off the saran wrap. The fix was a complete success and was undetectable. Your support rep. was excellent and I will use your company anytime that I need parts. Thank you. Dave Hathaway.