GTMP280GD4WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vicki from Redlands, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke off
Just popped the new door handle on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Dublin, OH
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The handle on the dryer broke off
I ordered the new part as listed and it came in two days, which was amazing to me since it was the week before Christmas. I snapped it in in less than a minute and all is well. Thank you for being so prompt on sending this out. Made the holidays a lot easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce R from Boca Raton, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Clipped on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Joliet, IL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pull door handle broke
No tools needed as old handle had come out on it's own when it broke. Simply removed duct tape that was used holding old one in place till new one arrived. Placed new one in position and snapped into place to hold. Less then a minute to install. Very pleased and surprised in how fast delivery of part from PartSelect was. Basically had it in 2 days. Will use them for other replacement parts as the need arises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from Middle Village, NY
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer will not turn on
replace control knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from flushing, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door handle to dryer broke...got part in 2 days,took 2 seconds to fix.
just 4 slots where the handle goes. Snapped handle into slots, good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Hilton Head, SC
- Parts Used:
- WE49X22295, WE20X20417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inside of door rusted
Very simple...just remove the inside of the door & replace.Great service on delivery of item ordered.quick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Cumming, GA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hilliard, FL
- Parts Used:
- WE14M104
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
burner assy rusted out at corners,spitting sound when on.
1. turn off gas.2. disconnect electric.3.Remove 3/8 gas line from rear of burner. 4.disconnect two electric connectors from gas valve assembly. 5.disconnect electric line from igniter. 6.remove two mounting sheet metal screws from front of gas valve assembly(5/16 socket). There also may be a screw holding assembly to the bottom plate.7. remove entire assembly from dryer by pulling out to the front. 8.remove igniter assembly and replace on new burner. 9. two sheet metal screws 1/4 inch hold burner assembly to gas valve assembly.10.Install in reverse order . it may take a few seconds for the gas to get down to the burner. don't forget to change over the air mix valve to the same place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from MOUNT AIRY, MD
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
timer and control knob
This repair is super easy. Take out the 6 phillips screws on the back of the control panel. Disconnect the timer wires and plug into the new timer--One wire at a time to make sure they fit into the same slots. Reinstall the timer and knob and back of the dryer and you are done. No need for a technican here. Save some $.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Lewisburg, TN
- Parts Used:
- WE04X20089, WE1M652
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
timer was getting hard to set and kept breaking the knobs, thanks to plastic shaft and plastic knobs
Very simple, if not for having to take off bifold door and dragging dyer out so I could get to it. Far as installation of replacement timer, could have done the job in 5 minutes or less. Removed 6 screws in back of control panel. Raised tab on old timer and twisted counter-clockwise. Removed one wire at a time from old timer and put on new one. After plugging all wires put new timer in slots and had to bend up tab somewhat so it would turn all the way. I did install a screw in the tab, that wasn't there to begin with. Lined up panel and installed all screws and bravo, works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Alpharetta, GA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer handle broke off
You guys are awesome! It took me less than 5 minutes to look your company up, place the order, and closeout. Vroom...the part was to me in 3 days! I simply took it out of the wrapper, pressed the tabs into the existing slots, and done. And that cost....baby it's good. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tarleton from Newport, RI
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original handle on dryer door broke off
Aligned new handle with slots in dryer door and snapped into place. It took 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stu from Allentown, NJ
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original dryer handle broke after 12 years
New handle popped on easily. After 2 weeks the replacement handle just broke.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vance from van hornesville, NY
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very good
ghanged the knob easy
Was this instruction helpful to you?
Thank you for voting!