DG750E*139 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Bordentown, NJ
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter screen was torn in several places over years of use.
Removed old lint filter and replaced with new one. Was impressed with the fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Magnolia, TX
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
dryer just quit
Checked out problem found belt broke and order part from part select and when it got in I replaced the belt and then found pully bad too. so I order that part from ya'll and it tok less than 5 mint to install. everything went very well and I and my wife are very happy with everything.
Thank's Partselect,
John& Roxanna
Thank's Partselect,
John& Roxanna
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Greenville, IL
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
loud squeeking noise when dryer was runnig
nd removed it from the unit.
5. replaced drum bearings
6. reassembled everything in the same order I took it off.
Be sure to mark any wires you may disconnect to ensure you connect them back correctly.
Was a bit frustrating at times, but made it through and there is no more squeek.
5. replaced drum bearings
6. reassembled everything in the same order I took it off.
Be sure to mark any wires you may disconnect to ensure you connect them back correctly.
Was a bit frustrating at times, but made it through and there is no more squeek.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from dayton, OH
- Parts Used:
- WE12X10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
The belt that turn dryer drum ; broke
unplugged dryer,removed air duct,,remove( top of dryer) by removing the two back screws.... removed two screws under (fornt top lid),laid top to the side. ...Now remove ( front of dryer) remove,two screws near the( top on the inside)...lean dryer back, and remove outsidescrews at the bottom)..the front should come off. ..located small square opening in the back of the dryer release clamp from drum ,...put belt around drum... put drum and dryer back together...(relace any electrical wires removed if any..remove (rear bottom plug panel)..you can now see the lower inside of dryer....make sure belt is level on drum by rotating...place belt on lower pully,... lift tension(spring pully) on to belt.. replace cover..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joanne from north palm springs, CA
- Parts Used:
- WE25X60
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
After Taking The Dryer Apart, I Can't Find These Parts .
After taking the dryer apart and not finding anything that looks like the one I have in this box that I ordered, I got the right part and dryer is working find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Medford, NJ
- Parts Used:
- WE4X197
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door switch failed
Make sure your power is off, When loosened the top and tilted back, the first thing I saw was the door switch, I guess I was just lucky I disconnected the two wires and checked it and it was bad. Got my new one from you and installed it. It has a ground terminal, which my model switch only had the two terminals. It working fine.I took the bad switch apart and the one leg on the copper U shaped contact had broken off. The Belt I have as a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jana from Eatonton, GA
- Parts Used:
- WE25X60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The dryer was making a very loud noise
After having a friend who repairs appliances come and diagnose the problem, I was able to find the parts I needed very easily at PartSelect. They came quickly and I removed the front panel, followed the instructions (they were not very detailed) and also had help reading some of the other posts from people on the website. I replaced the parts and the dryer is now quiet and running fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from North Branford, CT
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement part only
I did not have an actual repair. I simply replaced the lint filter that dropped into the receptacle. However, what I want to mention is that the part was available as old as the dryer is and there was a nice photo to scale of the replacement part so that I was sure I was getting the correct piece. A great site to obtain parts from my experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hendersonville, NC
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter plugged with lint
Just replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from Waterford, MI
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door wouldn't stay closed.
There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Montour Falls, NY
- Parts Used:
- WE4X444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
no heat
followed video direction ,pulled part ,compared to part on-line ,ordered part delivered in two buisness days and installed ,back in service .very simple and I will shop at your sight again and tell friends and family as well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Florissant, MO
- Parts Used:
- WE3X75
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
squealing noise while dryer was running
Removed two screws from front by door. Removed back panel to remove belt from tensioner. lifted lid of dryer. removed two more screws from inside to remove front panel. while holding the barrel I removed the front panel then grabbed barrel and pulled out. took off the old bearing, put the new one on and reassembled it the way I took it apart. The whole thing took about 10 min was quick and easy if there is any problems while you are doing it look it up on youtube.com and you can see it done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Redondo Beach, CA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not stay closed
inserted the latch into the opening in the front face of the dryer
Was this instruction helpful to you?
Thank you for voting!
Dryer did not start
Opened front door and removed 4 screws inside, lift the top cover disconected 2 wires and replaced the door switch. Because my dryer was an old dryer my door switch had 2 wires connected to the door switch new door switch had 3 connectors I called part select customer service and they instructed me to use the 2 small connector with the 2 wires that I have.
Was this instruction helpful to you?
Thank you for voting!