YD630S*459 General Electric Dryer - Instructions

inserted on an angle and snapped in place.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

replaced rear drum bearing kit Still makes the same noise

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Started with removal of rear inspection plate on rear of drier,rotated drier drum by hand to look for any visible problems. Found that drive belt with age had lost sections of teeth and every time the bad sections would go past motor they would "thump".
1. Removed belt from tensioner. Done simply by moving tensioner to unload belt.
2. Slipped belt off motor drive and moved belt to front of drum.
3. Opened drier door and removed 4 screws from under the lid or top of drier ,raised lid for access to belt once belt had been slid to front of drum.
4. (steps 4 and 5 are the hardest parts)Worked drive belt between drum and felt insulators keep in mind there are many stamped steel pieces and sharp edges can be present.
5. Removed belt by feeding a small section past felt and drum and worked rest out from frt. top of drier.
6. Installed new belt in reverse order as removal.
This was done without aid of instruction manual and by someone having major back surgery 4 months earlier. No idea how much this saved me but the price of the belt and time and effort involved made it woth my while I'm sure.

Your instructions were execellent
Problem is solve
Thank you

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.