64240419 General Electric Dryer - Instructions

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Your instructions were execellent
Problem is solve
Thank you

replaced rear drum bearing kit Still makes the same noise

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

Removed the top, front and lower rear section of the dryer. This being my first experience replacing a dryer belt I naturally missed the tensioner pulley first try, then installed the belt on the wrong side of the pulley and found I didn't have enough tension. After some thought and a long hard look I realized my mistake and the third time was the charm. Next time I need to replace a dryer belt it should be a snap and go a lot faster.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Started with removal of rear inspection plate on rear of drier,rotated drier drum by hand to look for any visible problems. Found that drive belt with age had lost sections of teeth and every time the bad sections would go past motor they would "thump".
1. Removed belt from tensioner. Done simply by moving tensioner to unload belt.
2. Slipped belt off motor drive and moved belt to front of drum.
3. Opened drier door and removed 4 screws from under the lid or top of drier ,raised lid for access to belt once belt had been slid to front of drum.
4. (steps 4 and 5 are the hardest parts)Worked drive belt between drum and felt insulators keep in mind there are many stamped steel pieces and sharp edges can be present.
5. Removed belt by feeding a small section past felt and drum and worked rest out from frt. top of drier.
6. Installed new belt in reverse order as removal.
This was done without aid of instruction manual and by someone having major back surgery 4 months earlier. No idea how much this saved me but the price of the belt and time and effort involved made it woth my while I'm sure.

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

I first removed four screws above the door opening to lift off the top, then removed two screws, near the top, inside the front, to remove the front. There I found that 2 grey plastic and one white plastic anti-friction strips were worn to nothing (even the large plastic bezel that incorporates the light was starting to wear away, from just a few days!).

When I went to put the front back on, i couldn't get the lip of the drum to ride properly on the felt. In fiddling with it, the drum fell off the rear bearing, too, so I put it back on.

So I ordered new felt, two white and two grey strips (I didn't know if 1 or 2 were in each $8 "kit"--only one per kit), a spare belt--just in case--and some bulbs.

Putting the strips on was easy--15 seconds each. Putting on the felt took all of 20 seconds. I spent more time scraping off the dust and vacuuming things out!

The drum fit over the felt quite easily now, and when I ran it, it was wonderfully quiet. For a minute! Then, it started making a new, grinding noise!

I had a Sears repairman friend come over, and he found that a small platic bushing had fallen off the rear bearing element. Once he put that in place, it all worked perfectly. Beautifully quiet!

The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.

Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.