633615 General Electric Dryer - Instructions

Opened panel, bent retainer tab, took off wires. Took out switch, put in new switch, replaced wires and knob and plugged it in. Off she goes. PS, how the hell did you get that part to me in less than 24 hours??? Thanks guys.

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

Took off old timer and put new knob on and it fit.

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

I read the other repair instructions on this site and looked at the parts diagrams. It wasn't entirely clear how everything came apart but once I started by unscrewing the top of the dryer and removing it (screws were just inside the dryer door) it was easy. Unscrewed the front panel next , swung it out, and it was quick work to install the new bearing with the slides. It wasn't too clear in the parts diagrams but I did need two each of the dryer drum slides and front dryer drum slides, four total, two on each side of the drum bearing. The dryer had been running on the old drum bearing itself, the old slides had worn completely down and the bearing itself was starting to disintegrate too. If I'd caught it sooner I could have reused the bearing and just replaced the slides. Saved a lot of $ and the dryer is nice and quiet again!

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!

I watched the repair video 3 times to make sure I was comfortable to do the repair.the video was very helpful.thank you ! Everything went well and the dryer runs great.

Fairly simple. removed start wwitch by rotating it out of its position. There is realy only one way to remove it and it is intuitive. The new part is simply placed n the only position that the part will fit in the panel. Once the part is locked in placed, the new part is installed. Simply take you time and think it thru.

inserted the lint catcher into the opening to replace the old one

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.

I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.

Opened up the package and took off existing door handle. The new one snapped right into place. This took all of 10 seconds!