63040459 General Electric Dryer - Instructions

r/r parts unit runs great

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

I first removed four screws above the door opening to lift off the top, then removed two screws, near the top, inside the front, to remove the front. There I found that 2 grey plastic and one white plastic anti-friction strips were worn to nothing (even the large plastic bezel that incorporates the light was starting to wear away, from just a few days!).

When I went to put the front back on, i couldn't get the lip of the drum to ride properly on the felt. In fiddling with it, the drum fell off the rear bearing, too, so I put it back on.

So I ordered new felt, two white and two grey strips (I didn't know if 1 or 2 were in each $8 "kit"--only one per kit), a spare belt--just in case--and some bulbs.

Putting the strips on was easy--15 seconds each. Putting on the felt took all of 20 seconds. I spent more time scraping off the dust and vacuuming things out!

The drum fit over the felt quite easily now, and when I ran it, it was wonderfully quiet. For a minute! Then, it started making a new, grinding noise!

I had a Sears repairman friend come over, and he found that a small platic bushing had fallen off the rear bearing element. Once he put that in place, it all worked perfectly. Beautifully quiet!

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

replaced rear drum bearing kit Still makes the same noise

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.

Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

it was easy, it clip right on.needed to give it a little tap to get it in .