64100169 General Electric Dryer - Instructions

Unplug the AC cord. Open dryer door and unscrew 4 small Phillips screws that hold the top panel to the front panel. Tilt up the top panel.
To remove the front panel: Look on the inside of the front panel, disconnect all the wire connections that go to/from the front panel, such as the light and door switch. Remove 2 screws that attach the top of front panel to the side panels using a 8mm or 5/16" wrench. Undo or loosen 2 Phillips screws at the bottom of the front panel, one at each bottom corner. Remove the front panel. Go to the back of the dryer. Remove the 8 screws holding the lower access panel (8mm or 5/16"). Remove the access panel. Also, remove the 2"x4" access plate in the center of the back panel (2 8mm/5/16"). Reach inside the small panel opening with a needle nose pliers and remove a Cir-clip and washer that holds the rear drum bearing shaft in place. Now you can remove the drum straight forward. Clean, clean, clean the insides. Replace the worn drive belt, follower wheel and front slider pads as needed. Reverse the procedure to reassemble. Plug in and test. Drink beer.

Easy repair, but did take a little longer than anticipated due to the extra cleaning that I did while the dryer was disassembled (highly recommend). First, unplug the power cord. Then, open the door, and locate the two screws in the upper corners, and remove. This will allow you to remove the top cover. Be careful and work the top panel up and down to loosen the control panel tabs, and set aside top panel. Next, remove the two screws located near the top on the inside of the front panel. Removing these two screws will allow you to lean the front panel forward, lift up, releasing the tabs holding the bottom of the panel. Be careful when you pull the front panel from the dryer as you will need to lift the drum off of the front bearing which is attached to the front panel as it is removed. You will also need to use your needle nose pliers to remove the wires prior to setting the panel aside. The wires are straight forward and power the light at the top, and the safety door switch. I always take a picture with my phone's camera just to validate when I re-connect them. Reaching underneath the drum you will be able to feel the belt and belt tensioner pulley. With both hands under the drum, use one hand to push the pulley to the right, releasing tension on the belt. Move the belt out of the groove, and let it hang freely. Now from the top of the drum, bump the drum to loosen, and remove from the cabinet. It is a tight fit, so you will need to spread the sides slightly in order to remove the drum. Next, remove the 3 screws holding the heat diffuser in the rear of the drum in order to remove the rear drum bearing. (Tip: It would be nice to have a helper hold the new drum bearing in place when starting the screws, and it also helped to tighten each a little at a time to keep the new bearing flat as it was drawn up next to the drum.) Tighten the screws holding the new bearing in place. Next, remove the 4 small screws holding the heating element housing to the rear of the dryer. (Tip: Rather than disconnecting the wires, I used a bent coat hanger to hold the housing while I removed the bearing retainer and clip from the rear of the housing.) Remove the 4 screws holding the bearing retainer and clip, and replace with you new part, paying close attention to the clip's position, and tighten. Replace the housing to the rear of the dryer. (Tip: Now is a good time to familiarize yourself with the belt and tensioner pulley for reassembly. Also, it may be a good idea to look at your belt, and replace as needed.) Next, reinstall the drum and insert the new bearing shaft into the new bearing housing. Using both hands again, reach underneath the drum, locate the tensioner pulley, and belt. Push the tensioner pulley over to the right, and move belt over the pulley on the motor, and behind the tensioner pulley. The belt should be tight. If not, inspect to ensure that the belt is over the motor pulley, and the tensioner pulley. Next step is to reinstall the front panel. I also spent the extra money and replaced the front drum bearing, and slides. Please note that the green slides are on top, and the white slides are on the bottom. Lift the panel over the tabs, lean forward while lifting the tub, resting the tub on the front bearing. Reinstall two screws in the upper corners, and tighten the front panel back in place. Now is a good time to turn the drum to ensure that the belt is in place, and that the drum turns correctly. (Tip: If your dryer is equipped with a light, you may also want to replace the bulb in the front panel (if needed) prior to attaching the front panel.) Reinstall the top panel by aligning the tabs in the control panel with the top panel, being careful not to bend the tabs. Next, open the front door and use the 2 long screws to reattach the top panel to the front panel. Plug in power cord.

Be sure to segregate and label all screws.
Remove back and front of control panel.
Removed dryer top.
Removed dryer front/door panel.
Replaced slides. Due to discoloration it was hard to tell the white fr the green. Double checked partselect videos to be sure which was which.
Propped up drum with the dowel to allow enough room to access the coils. One of the screws was frozen. Soaked in penetrating oil for 30 minutes. Then used a Philips headed socket to break it free. Used needle nose pliers to lift out old coils and to place new coils.
Reversed process to reinstall all panels.
Crossed fingers and tested. AOK.

I had never tried to fix a dryer before, but I checked your site and found detailed troubleshooting instructions. I found several parts diagrams that made me think it would not be too difficult. I found the GE Repair manual for my dryer and ordered it. I was able to determine that the sqeaking was in the front, and probably the slides were worn, as opposed to the drum roller. Whew! My daughter and I removed the front and checked them. They were totally worn away and the felt was crimped. We cleaned it up and ordered the replacement parts from you. When they arrived we made the repairs. One of the drum slide holders was too worn to hold the new slide so we applied a bit of super glue to hold it in place. My dryer is running quietly again. I am so glad for your online information. This was an fairly easy fix!

first I removed the screws with the nutdriver at the bottom of the dryer at the back..then I could see the belt was broken...next I took off the 2 nuts at the back that hold the top on ..then opened the dryer front door and unscrewd the 4 screws holding the top on....then I lifted the top up and to the side...then all I had to do was take out 2 screws one on each side of dryer front and the the front was open enough that I could slide the new belt on dryer..then screwed the front back on...then placed the top on and went to the back of dryer and put belt on pulley using the diagram I found in the instructions inside the dryer top...really a lot easier than it sounds...easy fix saved me from buying another dryer

First unplug dryer... very important. You have to identify the appropriate size socket wrench and locate all necessary screws to remove top panel of dryer and front panel. Locate belt drive. Remove old belt , replacing it with new belt attaching belt to dryer drum . Remove back panel of dryer to better reach and adjust belt onto tension wheels. Put dyer back together. YouTube gives you an idea of how to properly change a belt on dryer

I removed the right side panel and top panel from the dryer. I removed the 2 wire and 3 wire connectors from the 2 coils. I removed the bracket holding the 2 coils, replaced the 2 coils, and replaced the bracket. I reconnected the wires to the appropriate coils and replaced the side and tops panels on the dryer. The dryer now lights every time the dryer calls for heat.

Replaced High limit thermostat per video on the website. However, the flange of new thermostat is flat, while chassis it mounts on is round to conform to drum of dryer. So new thermostat was not flush with chassis. Dryer did not shut off early (that problem solved), but instead continued to dry clothes beyond time necessary. Note that old thermostat had one side of flange slightly bent and probably more flush with chassis, and better able to sense when hot temperatures were reached. I dismantled dryer again, slightly bent new flange, re-installed. Seems to work better now .

Top is hinged in back, removing the 4 screws over the door under the top allowed the top to open. Removing the 2 screws near the top of the door panel allowed it's removal. Marked and disconnected wiring. Lifted drum through top. New bearing housing required 3 mounting holes to be tapped to 10-24. Installed bearing and backing shims with old hardened allen head mounting screws inside drum while wife held bearing in back of drum. Furnished 3- 10-24 lock nuts to lock mounting screws in place from their back side. Reinserted drum through dryer top with belt on drum. Hardest part was getting the belt on motor pulley while holding the idler in it's correct position due to small access holes at the very bottom in rear panel. Works just fine again.

I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.

Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.

easy to fix took less than 10 minutes

Key starting point is to remove top cover by removing two long screws located at the front of the cover
Remove control panel and it's bottom and side supports.
Remove short vent pipe by bending retainer tab.
Support the drum at the top using piece of rope.
Remove main rear cover (leave bottom attached).
Remove electric heating unit and install new bearing carrier from kit.
Reinstall the the heating unit
Remove three screws (inside the drum)to release the inner drum cover and release the bearing carrier.
Install new bearing carrier. Note: the three holes in the bearing carrier are not tapped, I suggest that the screws be installed (threads cut) into the bearing cover before attempting to install the bearing carrier.
Install the new bearing carrier. Note: pilot one of the holes using a small nail etc. then go on to install screws in the other two holes remove the pilot device and install the third screw.
Reassemble in reverse order.