PSXH47EF1WW General Electric Dryer - Instructions

Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

This was a stacked washer and dryer combo and is a lot more difficult to repair, requiring a lot more to take apart and put back together.

Very simple. Pop the top open released the beld from the back it's easier that way the video was very helpful the sound was so bad you can hear it from a few houses down after year of just using it like that I figured I ha d nothing to loose great price great instructions now it sounds just as new.

Replaced everything on the dryer till I got the right problem, seriously, I now have a new dryer in an old body, still came out alot cheaper than buying a new one. I listened to every sound on youtube but none sounded like my dryer.

I watched the videos on this excellent website first. Then the repair was a breeze.

The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.

when the bearing broke the drum fell in the back. I tore the dryer apart, ordered the part and fixed it when the part came. the dryer runs like new now!

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!

I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.

Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.