PSXH43EC0WW General Electric Dryer - Instructions

purchased bearing kit

I set up my laptop with the partselect video going. Laid out my tools and the individual parts that were in the kit. I watched the video a segment at a time, performing the tasks in the same manner that the instructor did. All together, the process took less than two hours, I had no questions or difficulties, and the repair process went flawlessly and successfully. I had never done anything more complicated on a dryer than replacing the hose before this. The sense of pride in doing a repair of this level myself, and avoiding paying someone ridiculous fees to do it, is beyond description.

Basically followed the You tube videos on standard, stand alone dryers as mine is a stack-able unit. Allow a lot of room to work. Unplug electricity and or the gas, vent hose and water hoses. Start removing screws as per the video, remove Belt then lift up then out the dryer drum. (The drum drops in from above on the back of the unit)the rest is remove and replace as you go. *TIP... I use my phone to photograph tricky areas so I can review as needed. It was more scary then difficult. You can do it!

Replaced rear bearing on back of dryer. Repair cost $20.00 an a little time. Much better then buying a new dryer. It was easy to repair the video instructions were great. I would do it again it needed.

I ordered the rear drum assembly on Monday evening and the part came on Wed at 11 am. I started the repair at 1 and finished at 3. It would have been faster, but my computer kept freezing during the repair video. The video was so easy to follow. I could have used longer arms or a helper, but I managed to get the job done by myself. Needless to say, my husband was thrilled. Great service. Thanks

the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

followed vidio instruction which made it easy

The repair was done by my spouse. We replaced the rear drum bearing. We installed with the instructions sent by parts select. They were very accurate. The total repair took about 1 and 1/2 hours that was only because we cleaned out the entire dryer also, by using an air compressor to clean and blow out all the lint built up. This improved drying time and the part stopped the noise. I don't recall exactly what tools were used besides screwdrivers. This was our first time to replace anything in our dryer of 12 years old. I feel that if you follow the instructions that anyone would be able to do this repair. We did the repair in our garage because you need the room to work on it.

I watched the video and the instructions were perfect. The only thing I did differently was I had a second person help me to hold the bearing spring and hold the drum knob in place. I also used the rear access panel to disengage and re-engage the belt because I know I am not good at doing things blindly. You will definitely want to pre-thread the knob assembly before you screw it to the drum. Glad the kit included a bearing because the old one was completely gone. It took me so long because I took the opportunity to vacuum 10 plus years of lint and I was using it as a teaching opportunity. If I have to replace the heating element I think it will be much faster.

Followed the video, it was good, the instructor's tips were useful and time saving.

I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.

Followed video that was provided!! Now I know how to get the top and front of dryer OPEN. Now I can clean interior of dryer ALSO, lots of lent!!

It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.

followed the Video instruction which were provided. Dryer works like brand new.