GDV980K*429 General Electric Dryer - Instructions

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

Used online instructions. Worked well.

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

Your instructions were execellent
Problem is solve
Thank you

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

I first removed four screws above the door opening to lift off the top, then removed two screws, near the top, inside the front, to remove the front. There I found that 2 grey plastic and one white plastic anti-friction strips were worn to nothing (even the large plastic bezel that incorporates the light was starting to wear away, from just a few days!).

When I went to put the front back on, i couldn't get the lip of the drum to ride properly on the felt. In fiddling with it, the drum fell off the rear bearing, too, so I put it back on.

So I ordered new felt, two white and two grey strips (I didn't know if 1 or 2 were in each $8 "kit"--only one per kit), a spare belt--just in case--and some bulbs.

Putting the strips on was easy--15 seconds each. Putting on the felt took all of 20 seconds. I spent more time scraping off the dust and vacuuming things out!

The drum fit over the felt quite easily now, and when I ran it, it was wonderfully quiet. For a minute! Then, it started making a new, grinding noise!

I had a Sears repairman friend come over, and he found that a small platic bushing had fallen off the rear bearing element. Once he put that in place, it all worked perfectly. Beautifully quiet!

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

r/r parts unit runs great

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.