DCXH46EA3WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Ringgold, GA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Really Loud Squeeking Sound
I watched the videos on this excellent website first. Then the repair was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Staten Island, NY
- Parts Used:
- WE12X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the dryer belt broke
very simple my husband put it on in no time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Houston, TX
- Parts Used:
- WE01X10167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
install new knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Lindenhurst, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Old bearing made noise. Grease was dry and worn out.
The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Witly from Wheatley Heights, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum
I remove the drum, and install the bearing just like the instructions in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BOB from PRATTVILLE, AL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer Made Loud Squeal During Operation
I set up my laptop with the partselect video going. Laid out my tools and the individual parts that were in the kit. I watched the video a segment at a time, performing the tasks in the same manner that the instructor did. All together, the process took less than two hours, I had no questions or difficulties, and the repair process went flawlessly and successfully. I had never done anything more complicated on a dryer than replacing the hose before this. The sense of pride in doing a repair of this level myself, and avoiding paying someone ridiculous fees to do it, is beyond description.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jack from Post Falls, ID
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Rear drum bearing worn out
Basically followed the You tube videos on standard, stand alone dryers as mine is a stack-able unit. Allow a lot of room to work. Unplug electricity and or the gas, vent hose and water hoses. Start removing screws as per the video, remove Belt then lift up then out the dryer drum. (The drum drops in from above on the back of the unit)the rest is remove and replace as you go. *TIP... I use my phone to photograph tricky areas so I can review as needed. It was more scary then difficult. You can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from New London, NC
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was making a noise like scraching a black board.
The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert from Elizabethtown, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer Squeaking
Found instructions on "UTube"some of the screws were in a different position but you can see them. While you have the dryer apart it's a great time to clean it and also as long as you've gone this far replace the belt,it's probably time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from salem, OR
- Parts Used:
- 5303281153, 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Rear drum bearing kit had sheared off
Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Lake Mary, FL
- Parts Used:
- WE12X10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
noisy belt
Removed top of dryer, took screws out of back of dryer, pulled drum off front of dryer, removed old belt and slid new one in place. Reattached drum to front and slid belt in place only to find it was the wrong size. Called an appliance repair man, he said happens more ften than not.
Was this instruction helpful to you?
Thank you for voting!