DCXH46EA3WW General Electric Dryer - Instructions

I first diagnosed the problem using a Google search. Amazing how many hits I got and after reading a few was pretty certain what the cause was and what parts I probably needed to make the repair.
Some of the articles I read had links or mentioned PartSelect, so I searched for my model # and found the parts I would probably need. Knowing that I could probably get the parts I needed I disassembled the dryer (pretty easy really) and removed the old suspect part. It was devoid of lubricant and the bearing and ball showed some wear so I ordered the Bearing Assembly suggested by PartSelect (the illustrations looked just like my old parts). I left the dryer disassembled while I waited for the part, figuring it would take a week or so to arrive.
Much to my surprise, the part arrived three days later and after cleaning the dryer innards of all collected lint I put it all back together in 30 minutes.
So for a little research, a $30 part, and about an hour of my time, I have a clean and quiet operating dryer. I see no reason I can't get another 10 or so years out of it.
I consider myself a reasonably handy guy but had never worked on a dryer before. I'll be unlikely to ever call a repairman without first doing some investigation and seeing if the parts are available. With the internet and PartSelect I think I could take on a lot of other repairs I'm not familiar with. Thanks for a great outcome this time around.
Kevin

After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.

first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.

removed the drum out the front and replaced

First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.

i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in

Replace the Drum Bearing and Shaft

This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.

Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.

Followed others directions and it went very well. I could not believe how much lint was packed in the bottom of the dryer! Need to clean this area out perhaps once a year.

We had the rear drum bearing replaced about three years ago. The company that serviced it was quick to take our money for the diagnosis but took over a month (and a threat to call the better business bureau) to actually make the repair. This time I decided to do it my self as I had successfully replaced the the drum drive belt two years ago. The dissassembly was challenging but the repair it's self very easy. I opted to use nuts and bolts to attach the bearing assembly rather than the supplied screws as they did not want to tighten. Reassmbly was a bit of a challenge regarding the drum drive belt but I had the entire repair done in less than an hour.

There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.

FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.

The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.

Followed online video. All went smooth. Runs great!!!!!!!!!!!!!