65298429 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GUY from BEDFORD HILLS, NY
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum slide wore - damaged drum bearing
r/r parts unit runs great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Williston, VT
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer squeaks and squeals while running
Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from PLEASANT CITY, OH
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud screaching noise
We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from santa maria, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
squeaking
snap in snap out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROB from CLARKS SUMMIT, PA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud noise when running
I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Youngstown, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
making a bad noise in the rear
replaced rear drum bearing kit Still makes the same noise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Kalkaska, MI
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer wouldn't tumble
Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.
We are greatful for your service and really happy we didn't have to drive all over to find the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from lawrenceville, GA
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
with heavy load in dryer a loud scrapeing noise
Your instructions were execellent
Problem is solve
Thank you
Problem is solve
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Crystal Falls, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeaking when using dryer
It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edgar from Edmunds, WA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer Drum was squeaking.
Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Mount Juliet, TN
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud Grinding Noise
I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!
Thanks Parts Select for your help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from MECHANICSBURG, IL
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
for about 6 months our dryer has been making a sqealing noise and kept getting worst
I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACK from Fairfax, VA
- Parts Used:
- WE12X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The drive belt on the trusty GE dryer, bought used from a GI in Germany about 40 years ago and donated to our relatives when we returned to the States finally broke and I airmailed them a new one.
The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.
Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.
Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Winsted, CT
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud squeaking from dryer
Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Brunswick, GA
- Parts Used:
- WE12X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Belt broke, drum wouldn't turn.
Pulled the top of dryer off. Separated the door from the drum seal or gasket, slipped the belt through, put the drive belt on the motor and then put it all back together.
Was this instruction helpful to you?
Thank you for voting!