64325419 General Electric Dryer - Instructions

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

With my hands, a 2 yr old could of done it. But I was amazed how quickly I received the part. Thanks

That happened because the on/off selector nob broke, so I instructed my wife to use a small pair pliers to turn the stem as a work around until I could get to it (6 mos). It eventually broke off. I called a repair service that charges $90 to look at it, but cannot estimate the whole job. The dilemma is that the dryer is over five years old, so a repair costing more than a few hundred dollars is not as reasonable as buying a new dryer. What to do? I ordered the parts and diagrams on the internet. They arrived two days later. The dryer is jammed into a narrow space, so to see the two screws in the back, I needed a small mirror on telescoping wand. To get at the broken switch, I needed unscrew two "star" screws and remove the control panel facing. Not Phillips head, not a common slot head. This star screw is hard to find. I finally located it in the fastener section. I bought a bit that fit my stubby ratchet screw driver. I had to use the stubby screw driver because it was such a cramped space. I finally got at the switch, loosened one screw (hex head) and replaced the two wires on clips - no solder needed. Got a kiss and a squeeze from the missus and a load of clean clothes.

I got the parts & a friend did the repair. He removed the "cover" from the top of the dryer to install the new timer. He "plugged" it back in, put the cover back with the screw driver & replaced the knobs & the dryer was good to go. It was much easier than I thought it would be. Getting the parts from you guys was awesome - the delivery was so speedy. If I ever need parts for older appliances that I cannot find at a hardware store, I will most definitely order from you guys.

My son in law installed the new part, I didn't watch him so not sure how he did it, think he removed 6 screws, took the front panel off, installed the new part , took less than 15 minutes, now, dryer working again! Sure saved me money, of course, the dryer might die tomorrow from old age but today, working like a charm.

first I removed the screws with the nutdriver at the bottom of the dryer at the back..then I could see the belt was broken...next I took off the 2 nuts at the back that hold the top on ..then opened the dryer front door and unscrewd the 4 screws holding the top on....then I lifted the top up and to the side...then all I had to do was take out 2 screws one on each side of dryer front and the the front was open enough that I could slide the new belt on dryer..then screwed the front back on...then placed the top on and went to the back of dryer and put belt on pulley using the diagram I found in the instructions inside the dryer top...really a lot easier than it sounds...easy fix saved me from buying another dryer

* Please note, if only the starter switch peg is broken you do not need to replace the starter knob if it isn't damaged. The peg is not attached to the starter knob. You must replace the entire starter unit because the peg isn't detachable.

Remove the starter knob by gently pulling it towards you.

Remove the two screws on the bottom left and right sides of the front panel using an Allen Wrench.

On the rear panel of the dryer remove bolts using pliers or an adjustable wrench. Remove the back panel and place it to the side.

** Important ** Before disconnecting the wires from the starter unit take a digital photo (I used my cell phone) of the starter so you will know how and where to reconnect the blue and brown wires to the unit. Now, remove the wires.

Unscrew the bolt attaching the starter unit to the dryer. There's a hook on the back of the starter unit attaching it to the dryer. Push the starter unit downward to remove it from the dryer.

Take the new starter unit out of the box and connect it to the blue and brown wires. Refer to your photo for proper connection.

Insert the starter unit into the dryer and push it upward so the hook on the back of the starter locks onto the dryer. Screw the bolt back onto the starter unit to secure it to the dryer.

Replace the rear dryer panel and tighten all bolts.

Replace and tighten the two screws on the front panel of the dryer.

Replace the starter knob by lining it up with the peg shape and gently pushing it onto the peg.

You're done!!!

I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

Simply replaced it. I have ordered from Parts Select several times. Excellent customer service. They always have the parts that I need and ship them to me promptly. Great company!

Unplugged the machine.
Removed four screws from the top of the machine to uncover the top of the machine.
Pulled the leads off the broken switch.
In the future I will make a note of which lead goes where. There are only two ways.
Went to PartSelect.com and found the part in less than a minute by using their part finder.
Placed the switch through the original opening in the machine and reattached the leads.
Reattached the cover. Plugged the machine back in. Turned the switch and it started right up.

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

Took off old timer and put new knob on and it fit.