PSKS333EB0WW General Electric Dryer - Instructions

It just popped into place :)

replaced in same position was previously

removed old knob, cleaned surface under knob, sprayed metal knob on dryer with wd-40, put new knob on. useing the wd-40 makes the knob turn a lot easyer.

All I had to do was snap it on and was ready to go. How easy was that. Would order any other parts again.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

replaced rear drum bearing kit Still makes the same noise

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.

First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).

Looked on-line for new knob. At GE website, part was $20 + shipping. On Parts select, part was $14 + shipping. Ordered on Friday, part delivered to house on Saturday. Installed in less than a minute. It worked. Wife is very happy. Life is good again.

The repair was extremely easy. Just pulled the broken knob off and replaced with the new one. No tools required.

Before ordering from PartSelect I had checked both the original vendor and a local repair shop. The vendor had nothing, said try online. The shop said they could order it for twice the price.

PartSelect sent exactly what I needed pronto. I pulled off the old knob. I pressed on the new knob.
Done.

The repair was pull old one off and replace new knob. Receiving the new knob was amazing. Ordered one afternoon and received new part by 11 am next morning at regular shipping. You can't ask for anything better than that. Thank you

When the part came in the mail. I opened the packaging & just pushed the knob on to the metal post of the dryer. Voile that easy!