HTX24GASK0WS General Electric Dryer - Instructions

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

Followed the detailed instructions provided when I bought the parts at the online website. Very good directions diagrams/pictures and explanation of repair effort required

I yanked on the piece of twisted felt and pulled it from between the drum and the frame. Model number and serial number were gotten from the placard inside the door frame. A schematic was found on line and the part ordered from that picture. The whole thing is held together by four Phillips head screws. Two are upside down in the top of the door frame on either side. A hand held impact driver with a #2 Phillips bit was necessary to dislodge those two screws. The remainder of the job was done with just a #2 Phillips screwdriver. After the two upside down screws are out the top just lifts off. It's held at the back only by location slots. The two remaining screws are under the top on the extreme left and right of the front and face downward. These hold the front door panel onto the frame. Be careful when removing the front panel with the door on it as there are wires near the bottom left corner that must not be ripped out of the door panel. What remained of the old gasket was removed from the grooves in the plastic inner panel upon which the front of the drum rides. The new gasket was put in place in that groove. Reassembly is just the reverse of disassembly. There's no reason to tighten down the two screws holding the top on with the impact driver when putting it back together.

very easy

Your site offered a video tutorial that removed any anxiety about doing the repair correctly. Removed front of dryer, disconnected wire assembly going to the front, replaced seal in seconds, returned dryer to original set up. simple. luckily. very easy to use website.

Watch the video on how to replace the belt on PartSelct site belt installation page.

The repair was easy. First I took out 2 screws. Then I lifted off the top. Next I unscrewed 2 to take off front. I leaned off the front and reached in got out old gasket. Replacing new gasket went right around top front panel under the clips. Putting front on and returning 2 screws. Then Same for top. Dryer runs and sounds like new. Thank You for your quick mail and easy help?

Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.

replaced felt on inside door that drum rides on

I used these two videos to help me clean the inside of the machine, then change the drive belt.

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Unplug the dryer. On the back, I unscrewed the top three screws that hold on the instrument panel and (from the back) slide the panel to my left to disconnect from the top. I opened the dryer door and removed the two screws on the inside top of the doorway to remove the top panel of the dryer. Inside the top of the dryer are two screws to remove so that I could swing the front panel of the dryer out to replace the lower front felt drum seal. I needed to use wd-40 on these screws. When the panel opens, there is no way to disconnect the wires to remove the panel, so I had to prop it up with something so it didn't tip over and damage the wiring; a sturdy chair worked. Then, I heared the drum pop off and drop down a little. I replaced the seal according to the video; by putting it in the groove and pressing it down into the tabs with a flat head screwdriver or something smooth with a little of the seal hanging over the groove at each end. While I was in there, I cleaned out the lint and the wd-40 I used earlier. Then I closed the panel, lifting the drum back into place, ensuring that the dryer drum would turn before and after I replaced the screws. I replaced the top panel and the screws inside the dryer door and slid the instrument panel back into place and replaced those screws. The dryer works great and very quietly now!

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

Removed gas line. removed control panel, removed top, removed front, removed burner, replaced igniter, put back in. paused and played the video. very easy to do. 42 minutes and I had a few beers.