Models > GTX18PSSJ0WW > Instructions

GTX18PSSJ0WW General Electric Dryer - Instructions

Jump to:

All Instructions for the GTX18PSSJ0WW
121 - 135 of 323
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Bruce from CHANUTE, KS
Parts Used:
WE05X20431, WE4M181
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Dryer was over heating and shutting off after like 5 minutes, the back was hot to touch..got the cycling thermostat problem solved
4 screws to open it up,pull out the wheel and there it is on back . Pretty easy..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Francisco from WEST COVINA, CA
Parts Used:
WE4M181
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
was not heating cheak parts select they recomended to purchaged the thermostat check vidio for installetion now working fine thanks
watched vidio from the site.just follow the instructions, And was able to fixed the problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff D from NEW MEADOWS, ID
Parts Used:
WE03X29897
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Darryl from FARR WEST, UT
Parts Used:
WE17X22217
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phuc from WOODBRIDGE, VA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Laurel Springs, NJ
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minutes or less.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Forrest from Mays Landing, NJ
Parts Used:
WE14X25080
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Cracked air duct
Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from EPHRATA, PA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael E from Victoria, TX
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
Dryer Belt Broke
After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from CHARLOTTE, MI
Parts Used:
WE04X20415
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
The dial on the timer would no longer engage (knob would just spin)
I followed the Youtube video created by PartSelect and it was SUPER easy.
Removed dial from front panel
I unscrewed the back panel, which released the knob panel on the front and tipped that forward to access the timer device.
Released the locking tab and spun the entire timer counter clockwise until it released. Pulled each connecting wire off and immediately replaced it on the new timer so I didn't mix up the order.
Once wires were attached, I replaced timer turning clockwise until it locked in place.
Re-positioned front panel and replaced back panel installing screws.
Replaced dial and dryer was ready to go!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Doug from INMAN, SC
Parts Used:
WE18X25100
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Danny from DOVER, AR
Parts Used:
WE01X20419
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from HUNTINGTN BCH, CA
Parts Used:
WE04X20415
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Dryer timer wasn’t working with auto dry or time dry
When I ordered it in the email receipt were directions- just click installation instructions- I also looked at u tube video by just typing in GE Dryer timer repair. It took longer to clean the floor where the dryer sat for years since we never move it. Cleaning time is included in the 15 minutes— You will feel great since just saved a ton of money. So glad I found you for future issues with appliance repair. There are U Tube videos to fix everything. Robert Maheu Huntington Beach
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Maryanna from GLENN DALE, MD
Parts Used:
WE01X22617, WH01X10106
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Knob popped off
I returned the part because it did NOT fix my washer knob! The part did NOT FIX THE KNOB. I am waiting for MY REFUND PLEASE!!

https://www.easyapplianceparts.com/PartSearchResults.aspx?ModelNum=GTW180SSJ0WW&mfgModelNum=&fkmfgID=2&Hint=knobs
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cheryl from WILDER, KY
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Door handle broke
Called my son-in-law. Easy as pie
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTX18PSSJ0WW
121 - 135 of 323