GTD33EASK0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from MEMPHIS, TN
- Parts Used:
- WE04X25280
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
the part where the knob went that part broke
pulled off the existing wires and made sure that they went back on the new one in the same place. then took off the existing screws. then took out old timer. replaced the wires on the right connections on the new timer then put the timer back in its position and tested it. the dryer turned on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from MONROE TWP, NJ
- Parts Used:
- WE04X25280, WE01X24552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced timer
Very good. Really only one screw holding the timer in place. It was a little difficult finding the right tool to use to remove that screw. But, once found, it was a easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from phenix city, AL
- Parts Used:
- WE03X31620, WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
belt was broken.
remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jena from BARDSTOWN, KY
- Parts Used:
- WE04X25280
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Timer stripped dryer wouldn't start
I unplugged the dryer from the wall. I took the back off which was simple then I took pictures of all wires connected to timer switch and then I disconnected the switch and looking at my pictures got the wires connected to the new timer. Put it all back together plugged it back in and was back in business. I'm a 37 year old female massage therapist and this was my business dryer I was fixing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from JASPER, GA
- Parts Used:
- WE04X25280
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old timer froze, wouldn’t advance
Removed old timer, 2 screws. Plug and play.
Very easy install.
Very easy install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary jane from NEW BERN, NC
- Parts Used:
- WE01X24552
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Dryer wouldn’t run-knob wouldn’t catch when turned
I researched the problem-ordered the part-watched a tutorial on Part Select website and replaced the old part with the new-couldn’t have been used asier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from DENISON, TX
- Parts Used:
- WE04X25280
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer was overheating, found that the timer was not working. Replaced timer and new timer does not work either. Replaced High limit thermostat part number 12073908 and dryer still runs to hot and new timer still don't work. Now looking for and suggestions on what the problem might be.
Replaced the timer. did not fix the overheating problem, replaced the High limit thermostat and that did not fix the problem, new timer does not function, does not time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARTIN from MOUNTAIN VIEW, WY
- Parts Used:
- WE1M825
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
WAITING ON PART
Still waiting for your parts. over two weeks to get part which was a hinge for something, I don't know what, but not my dryer seal. You said you would refund shipping and wrong part and charge me for a new order. End result was I got charged extra shipping for your mistake. The part still is MIA and it has been 5 weeks since I originally ordered. Will never do business with you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from WESTMINSTER, MD
- Parts Used:
- WE04X25201, WE04X25194
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer runs no heat,
Check for 240 at back of dryer, replaced all three thermostats around coil on rear panel, including high limt thermo,, but still no heat.
Not sure if coil is bad or if there is another thermostat or fuse around blower.
Not sure if coil is bad or if there is another thermostat or fuse around blower.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ruoli from Germantown, MD
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer's drum doesn't run
Follow YouTube "how to change dryer's belt" some video is very clear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvino from newtown, CT
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer belt was broken
I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Poughkeepsie, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Not Starting
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from NEW PRT RCHY, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
Was this instruction helpful to you?
Thank you for voting!