GTDP200GF3WS General Electric Dryer - Instructions

To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.

Replaced new screen in place of old one.

First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine

Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.

My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

I pulled the old handle off and pushed the new one on.
No problem at all.

remove the old one and put the new one...!!! Easy

Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minutes or less.

just replaced the unit handle and how my wife can open the dryer without a screwdriver

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Removed 4 #1 Philips screws from 1side and add to the other side.

1. Firmly grasp broken knob and pull it off.
2. Line up knob with post and push new knob on to post.
3. Quietly drink a beer and watch NFL mobile on your phone In the laundry room for a minimum of thirty minutes. ( For best results and to keep you from walking into the kitchen, stash a beer in the laundry room before you begin.)
4. Before leaving laundry room, do fifteen jumping jacks and twenty push ups-- enough to get your face red. Sprinkle some dryer lent in your hair. Crush can and throw it behind the dryer, no one ever looks there.
5. Immediately find your wife upon leaving the laundry room, and explain to her that the dryer is now fixed, you are exhausted, and need to take a nap.

When I ordered it in the email receipt were directions- just click installation instructions- I also looked at u tube video by just typing in GE Dryer timer repair. It took longer to clean the floor where the dryer sat for years since we never move it. Cleaning time is included in the 15 minutes— You will feel great since just saved a ton of money. So glad I found you for future issues with appliance repair. There are U Tube videos to fix everything. Robert Maheu Huntington Beach

Just slid right on.