GTD45EASJ2WS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alvino from newtown, CT
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer belt was broken
I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from SILVER SPGS, FL
- Parts Used:
- WE04X28977
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
When the door is closed the dryer didn't work
Easy watch YouTube and open door placed screwdriver under door switch pry lightly and switch will pop out unplug wire connectors and replace on new switch reinsert switch should be done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauren from WESTLAKE, OH
- Parts Used:
- WE03X25576
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer was making a lot of noise and clothing would get stuck along the drum
UNPLUG THE DRYER FIRST!!!
1. Open the dryer door and unscrew two screws connecting to the the top of the dryer.
2. Lift the dryer top and then pull the front of the dryer away from the frame (it should be a lift and pull motion)
3. Disconnect the power cord that runs to the dryer light
4. Unscrew the bearing top from the dryer front and pop the old bearing top assembly out
5. Insert the new bearing top assembly and reverse steps 1-4 to finish the install.
I recommend that while you have the dyer opened, you take the time to clean out any dust and lint from the interior.
1. Open the dryer door and unscrew two screws connecting to the the top of the dryer.
2. Lift the dryer top and then pull the front of the dryer away from the frame (it should be a lift and pull motion)
3. Disconnect the power cord that runs to the dryer light
4. Unscrew the bearing top from the dryer front and pop the old bearing top assembly out
5. Insert the new bearing top assembly and reverse steps 1-4 to finish the install.
I recommend that while you have the dyer opened, you take the time to clean out any dust and lint from the interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gonzalo from Haines City, FL
- Parts Used:
- WE03X25576
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Noise when drum is spinning.
I removed the top and front panel with door. Removed the bearing top assembly and install the new one. Then I reinstall the front panel with door and top panel in that order. Plug and play!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from LEVITTOWN, PA
- Parts Used:
- WE11X21156
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
no heat from dryer
used you tube and with your info. actually took apart dryer replaced part & reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Poughkeepsie, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Not Starting
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from NEW PRT RCHY, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DECATUR, GA
- Parts Used:
- WE03X37320, WE03X37319
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Replace the front slides and glides on the dryer
To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LEWES, DE
- Parts Used:
- WE01X24552
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Original timer knob stripped - actually this is the second one to do so.
Simply removed clip from the old knob - which had cracked - from stem, and attached replacement but bought a spare this time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from N FT MYERS, FL
- Parts Used:
- WE01X24552
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer timer will not work, can not engage timer.
Put new handle on timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bristow, VA
- Parts Used:
- WE03X37320, WE03X37319
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Rubbing noise while dryer was running.
After watching the video, the repair was very simple. There were no hiccups along the way. Special mention: the customer service is the best I've ever interacted with. Thank for making this a stress free experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Wynnewood, PA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb dead
remove the old one and put the new one...!!! Easy
Was this instruction helpful to you?
Thank you for voting!