GTDL210GD2WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Enterprise, AL
- Parts Used:
- WE1M462
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
With the help of doityourself guy on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from ABERDEEN, MD
- Parts Used:
- WE01X20374
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
timer would not turn
UN PLUG DRYER used screwdriver to remove 3 screws on back panel took control pannel and slid to the left to sepreat boyh panels used paper and pen to make picture of wires . push down on 2 side tabs turned timer and removed took off wires.to install just reverced process when done install knob and test,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from COMSTOCK PARK, MI
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squealing as drum rotated
Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Kissimmee, FL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MEMPHIS, TN
- Parts Used:
- WE18X25100, WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old dryer filter was cracked and bulb burnt out
Easy peasey! Just Removed/Replace screw-in type bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from SAINT AUGUSTINE, FL
- Parts Used:
- WE01X20374
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Timer knob stopped working
I took the new knob and stuck it on the shaft. That’s all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bud from RCH CUCAMONGA, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken door handle
Snapped right into place , less than a minute, if that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SONOMA, CA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
thumping noise with any kind of load
looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from LOVELAND, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken lint filter.
Removed the broken lint filter and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erica from ATLANTA, GA
- Parts Used:
- WE01X20378
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer was not turning on.
I bought all three parts but I noticed that the dial was very loose. I reapaired this first and it was working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from MORGANTOWN, WV
- Parts Used:
- WH01X10106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The timer knob was cracked and the metal "D"-Ring was broken on my GE cloths dryer
This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from West Bloomfield, MI
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic handle in dryer broke off.
All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from pleasant grove, AL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic Door Handle Cracked
Old handle popped out by pulling back and out. Inserted new handle by pushing in and forward. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Nora Springs, IA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom part of handle was loose
Opened up the package and took off existing door handle. The new one snapped right into place. This took all of 10 seconds!
Was this instruction helpful to you?
Thank you for voting!