GTX42EASJ0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gayle from Philadelphia, MS
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer wasnt drying as fast and was making a lot of noise.
Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Santa Barbara, CA
- Parts Used:
- WE09X27634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
clothes getting caught on the rim of the dryer drum
Watched the video associated with the repair and followed the instructions, it was easier that I thought it was going to be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Raleigh, NC
- Parts Used:
- WE09X27634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer made a very annoying high pitched scrapping/squealing sound
Followed the detailed instructions provided when I bought the parts at the online website. Very good directions diagrams/pictures and explanation of repair effort required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Stamford, NY
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Felt gasket found twisted between drum and frame
I yanked on the piece of twisted felt and pulled it from between the drum and the frame. Model number and serial number were gotten from the placard inside the door frame. A schematic was found on line and the part ordered from that picture. The whole thing is held together by four Phillips head screws. Two are upside down in the top of the door frame on either side. A hand held impact driver with a #2 Phillips bit was necessary to dislodge those two screws. The remainder of the job was done with just a #2 Phillips screwdriver. After the two upside down screws are out the top just lifts off. It's held at the back only by location slots. The two remaining screws are under the top on the extreme left and right of the front and face downward. These hold the front door panel onto the frame. Be careful when removing the front panel with the door on it as there are wires near the bottom left corner that must not be ripped out of the door panel. What remained of the old gasket was removed from the grooves in the plastic inner panel upon which the front of the drum rides. The new gasket was put in place in that groove. Reassembly is just the reverse of disassembly. There's no reason to tighten down the two screws holding the top on with the impact driver when putting it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from PROVIDENCE, RI
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drive belt broken....
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- monte from clayton, NJ
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Lower Front Felt Drum Seal failed and was flapping inside the dryer drum
Your site offered a video tutorial that removed any anxiety about doing the repair correctly. Removed front of dryer, disconnected wire assembly going to the front, replaced seal in seconds, returned dryer to original set up. simple. luckily. very easy to use website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Pascagoula, MS
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace light bulb in drum.
Unplug dryer, unscrew bulb then replace with a new bulb. Plug dryer back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Sunrise, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not tumble - heat but no drum rotation
Watch the video on how to replace the belt on PartSelct site belt installation page.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Hollywood, FL
- Parts Used:
- WE09X27634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My drum gasket needed to be replaced.
The repair was easy. First I took out 2 screws. Then I lifted off the top. Next I unscrewed 2 to take off front. I leaned off the front and reached in got out old gasket. Replacing new gasket went right around top front panel under the clips. Putting front on and returning 2 screws. Then Same for top. Dryer runs and sounds like new. Thank You for your quick mail and easy help?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald C. from Smithtown, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Drum wouldn't turn, snapped drive belt
Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Surfside, FL
- Parts Used:
- WE4M325
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Terminal block was burned
Before removing the old part,took photo with my phone camera to document the color wires hook up. Screwed in the new part and hooked up the color coded wires using the photo as reference. I was surprised how easy it was. Thanks. Partselect gave me fast shipping, cheap price and great customer service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Tiverton, RI
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
loud noise, rumble
replaced felt on inside door that drum rides on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from San Dimas, CA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sqeaking during operation
I used these two videos to help me clean the inside of the machine, then change the drive belt.
Was this instruction helpful to you?
Thank you for voting!