GTX60EBSJ0WS General Electric Dryer - Instructions

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

it was easy, it clip right on.needed to give it a little tap to get it in .

4 screws, that was it

open the dryer door, locate the 2 screws that hold the top in place, unscrew them

then locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew them

allow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)

lower top of dryer back in place, being careful to make sure the top clips back in correctly.

re-install the 2 screws that secure the dryer top to the front.

boom, you are done....

Amazingly easy work...

first ,removed two screws from inner door lining.removed top by lifting front up and off.removed two screws holding front panel onto side panels.lift and pull up front panel away from main body of dryer.turned it around watching not to damage wires. remove old felt and install new felt.put everything back together in reverse.dryer works great.

no problem open top remove front install new belt

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

Watch the video on how to replace the belt on PartSelct site belt installation page.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

I'm a 90 pound mother of 4you and was able to fix this problem all by myself. Very easy!

My son ordered the part, but gave up installing it. We called in a professional appliance repairman because the dryer had to be partially dismantled to remove the drum and a belt so three sets of holes could be aligned to secure the replacement diffuser. My daughter had to lend a hand to hold one piece in place while the repairman threaded the screws because the drum was too deep for him to be able to reach both front and back pieces. Definitely not a one-person job for this particular model.

Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.