GTDP490GD7WS General Electric Dryer - Instructions

Unplugged dryer from power source. Unscrewed holding plate (1-screw) and back plate (5-screws). Took photo of old timing unit while it was still mounted on the dryer to show wire correct wire connections. Used needle nose pliers to remove connecting wires one at a time from old timing unit and attached them to new timing unit. Reinstalled back plate and holding plate.

Tried to replace with home-store bought 6w light. Looked the same, fit into socket, but didn't work. Actually exploded when I turned it on! Be sure to use OEM part like this one. Worked perfectly!

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.

Very easy! Removed old parts, and installed new parts in reverse order. Dryer was running, and sounded like a new appliance in 35 minutes!

Generally followed directions by another customer that was provided with order. Much appreciated for this DIY. Do have extra comment so here goes.
1. Unplug dryer from wall and remove existing control knob.
2. Remove three screws on back of control compartment and fold the front forward.
3. Remove tiny anchor screw for timer and twist loose.
4. Transfer wire from old to new one at a time. (Extra comment - I thought at first there was problem with new timer because there were more wires than connectors. Some of the wires had double connectors. That hiccup in installation was caused by my inexperience with this first time effort.)
5. Reconnect timer to dryer compartment with tiny screw.
6. Replace three screws on back.
7. Add new control knob, plug up dryer, and it is done.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

1. Firmly grasp broken knob and pull it off.
2. Line up knob with post and push new knob on to post.
3. Quietly drink a beer and watch NFL mobile on your phone In the laundry room for a minimum of thirty minutes. ( For best results and to keep you from walking into the kitchen, stash a beer in the laundry room before you begin.)
4. Before leaving laundry room, do fifteen jumping jacks and twenty push ups-- enough to get your face red. Sprinkle some dryer lent in your hair. Crush can and throw it behind the dryer, no one ever looks there.
5. Immediately find your wife upon leaving the laundry room, and explain to her that the dryer is now fixed, you are exhausted, and need to take a nap.

Took back off control,panel. Took the timer out from the back, but left all the wires on. Took one wire off at a time and installed that wire on the same terminal on the new timer and did the same for all wires, one at a time. Replaced timer. Tried timer. It worked great. Buttoned up back and pushed dryer back in place.

Received the dryer knob, aligned the part and it went on with no tools, no labor.

Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!

Took 3 screw out and unplug 7 wires , and put it back the way it was . Very easy , 30 min
Thanks partselect for getting the past here fast