GTDP490ED8WS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from HOPKINS, MI
- Parts Used:
- WE14X25080
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
a lot
started with replacing the belt and tension pulley which I purchased from another source. I found your videos on line and they are great. easy to follow. Realized I needed the bottom vent assembly and your prices were better than my local supplier. It was easy to replace thanks to your video. It was nice that you included it in the final order status. The only problems. Did not know the duct felt seal was included with the new duct assembly. I ordered the wrong bearing slides, web site showed both green and white for my model. I now realize I should replace the upper bearing housing. Can I return the unused parts, unopened and have that put as a credit to my next order? Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DECATUR, GA
- Parts Used:
- WE03X37320, WE03X37319
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Replace the front slides and glides on the dryer
To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from NEW PRT RCHY, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from E LIVERPOOL, OH
- Parts Used:
- WE01X20380
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Control knob broke
Pulled the knob out of the package,went downstairs to basement, put the knob on the dryer, walked away with a fixed product. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from GALES FERRY, CT
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken piece
Snap out the broken part. Snap in the new part. Use caution with the wires, but don’t have to disconnect them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Wake Forest, NC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old screen was not sealing properly
Replaced new screen in place of old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WARRIOR, AL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased a used dryer & lint filter had holes due to rust
On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEOMINSTER, MA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb was intermittently working
Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from EDGEWATER, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
take the old dryer lint screen out
Hand replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Niceville, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic tab broke on handle --- temp taped on.
My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from EDGEWATER, FL
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My last phase of repairs of minor items.
if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from DOVER, AR
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffry from ROCKVILLE, MD
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Was this instruction helpful to you?
Thank you for voting!