GTDX185ED4CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donnie from KATY, TX
- Parts Used:
- WE4M533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer timer kept cutting off
Ordered new timer and installed . Really easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from KATY, TX
- Parts Used:
- WE4M533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Timer in Timed Dry cycle stopped at 50 minutes.
Unplugged dryer from wall.Removed 3 screws from the back that held the front face plate on. Pulled face plate away and to the right to release it from the dryer. Lifted the locking tab slightly and turned the old timer counter clockwise to remove. One at a time I removed a wire and connected it to the new timer. Installed new timer to the back of the face plate. Pushed on timer knob so I could hold the back of the timer to get it all the way on to the shaft. Lined up the three tabs at the bottom of the face place and slid it to the left , pushed the face face into place and secured it with the 3 screws. Plug Dryer back in. Done in less than 10 minutes. Dryer now works properly again. I know I saved myself a lot of money doing the repair my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Wallingford, CT
- Parts Used:
- WE4M137
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer would shut off on heat dry after a couple of minutes. I could feel the heat working. It would only continue to run on fluff/no heat
Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from POTTSVILLE, PA
- Parts Used:
- WE4M181
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Heat thermostat,now replacing the drum bearing with your kit..
By watching your video which was very helpful as I never made this repair before. All worked out fine. Since then I have ordered other parts., (drum bearing kit, door slides and a new belt.) The video on replacing the drum kit is very helpful too. One other fact is prices beat all other sites I looked and when I'm done the dryer will be "rebuilt" I recommend your parts to everyone., they are great quality.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MIDDLETOWN, NJ
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Popped in the new lint trap . Easy peasy
Pull the old lint trap out. Slid new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Pittsburgh, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door handle of our dryer broke off
After removing pieces that were stuck in the door, I simply popped the new handle in place. It took less than a minute. What was the easiest was ordering and receiving the new parts- I ordered and 2 days later I received the new parts. I didn't expect to get the new parts for at least a week.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from St Johns, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Handle had broken
inserted on an angle and snapped in place.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACK from HOT SPRINGS, AR
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter and mesh was worn out
It went perfect , just put it in. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Vista, CA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb blew out inside the dryer
Screwed the light bulb into the socket (duh)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrienne from Bonita Springs, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
new dryer filter
I ordered the part via the internet. The shipping date was delayed twice but you excellent customer service department followed through and expedited the order. I installed it myself. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lumberton, NJ
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic door handle broke
Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Southampton, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
After 12 years the handle on my GE washing machine broke.
Simply pulled off the old handle and snapped in the new one! No tools required. Took about 5 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Crest Hill, IL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Door Handle broke
This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shelly from layton, UT
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastiic door handle broke off my GE dryer
As soon as the new door handle arrived, I just snapped it into place. It took about two seconds>
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cumming, GA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just cliped it in the holes
I broke the handle
Was this instruction helpful to you?
Thank you for voting!