GFDN120ED3WW General Electric Dryer - Instructions

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

I used these two videos to help me clean the inside of the machine, then change the drive belt.

The repair was easy. First I took out 2 screws. Then I lifted off the top. Next I unscrewed 2 to take off front. I leaned off the front and reached in got out old gasket. Replacing new gasket went right around top front panel under the clips. Putting front on and returning 2 screws. Then Same for top. Dryer runs and sounds like new. Thank You for your quick mail and easy help?

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Watched the video associated with the repair and followed the instructions, it was easier that I thought it was going to be.

Followed the detailed instructions provided when I bought the parts at the online website. Very good directions diagrams/pictures and explanation of repair effort required

the replacement part was easy to replace but remembering how the belt went back on took alittle more time..

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

I yanked on the piece of twisted felt and pulled it from between the drum and the frame. Model number and serial number were gotten from the placard inside the door frame. A schematic was found on line and the part ordered from that picture. The whole thing is held together by four Phillips head screws. Two are upside down in the top of the door frame on either side. A hand held impact driver with a #2 Phillips bit was necessary to dislodge those two screws. The remainder of the job was done with just a #2 Phillips screwdriver. After the two upside down screws are out the top just lifts off. It's held at the back only by location slots. The two remaining screws are under the top on the extreme left and right of the front and face downward. These hold the front door panel onto the frame. Be careful when removing the front panel with the door on it as there are wires near the bottom left corner that must not be ripped out of the door panel. What remained of the old gasket was removed from the grooves in the plastic inner panel upon which the front of the drum rides. The new gasket was put in place in that groove. Reassembly is just the reverse of disassembly. There's no reason to tighten down the two screws holding the top on with the impact driver when putting it back together.

very easy

Watch the video on how to replace the belt on PartSelct site belt installation page.

Watched the video on YouTube and everything went great!

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

Your site offered a video tutorial that removed any anxiety about doing the repair correctly. Removed front of dryer, disconnected wire assembly going to the front, replaced seal in seconds, returned dryer to original set up. simple. luckily. very easy to use website.