EGD4000B0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from Sacramento, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer drum squealling
I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce R from Boca Raton, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Clipped on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie C. from North Hollywood, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door broke off.
It was so easy, I just depressed a couple of tabs and it popped right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Plattsmouth, NE
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Load Noises when dryer was running
Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Redlands, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke off
Just popped the new door handle on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AMY from RICHMOND, VA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broke off
Very satisfied. I simply took the plastic door handle out of the package and snapped it into the door. It popped right in and fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cypress, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic handle broke off.
Removed door and two screws to replace the door handle. Reassemnled in reverse order. It was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cumming, GA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just cliped it in the holes
I broke the handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Crest Hill, IL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Door Handle broke
This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shelly from layton, UT
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastiic door handle broke off my GE dryer
As soon as the new door handle arrived, I just snapped it into place. It took about two seconds>
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Southampton, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
After 12 years the handle on my GE washing machine broke.
Simply pulled off the old handle and snapped in the new one! No tools required. Took about 5 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd E from Eaton, OH
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
makeing a squeaking noise
remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it
todd e line eaton ohio usa
todd e line eaton ohio usa
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Joliet, IL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pull door handle broke
No tools needed as old handle had come out on it's own when it broke. Simply removed duct tape that was used holding old one in place till new one arrived. Placed new one in position and snapped into place to hold. Less then a minute to install. Very pleased and surprised in how fast delivery of part from PartSelect was. Basically had it in 2 days. Will use them for other replacement parts as the need arises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Fort Washington, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeeky Noise When Dryer Was Running
First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Peoria, IL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the dryer had a lovely squeak
I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.
Was this instruction helpful to you?
Thank you for voting!