DNSB514EB0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deborah from Dublin, OH
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The handle on the dryer broke off
I ordered the new part as listed and it came in two days, which was amazing to me since it was the week before Christmas. I snapped it in in less than a minute and all is well. Thank you for being so prompt on sending this out. Made the holidays a lot easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Sacramento, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer drum squealling
I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce R from Boca Raton, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Clipped on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from flushing, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door handle to dryer broke...got part in 2 days,took 2 seconds to fix.
just 4 slots where the handle goes. Snapped handle into slots, good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from Belhaven, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Handle on dryer door broke off
All we had to do was snap it back into place on the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from LIncoln, NE
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Intermittent squeak when first starting the dryer.
Followed the video on this site but did not have to remove wires. Just stand in front and let the front panel rest on your leg while you replace the slides. Quick and Easy!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana M from Middleport, NY
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Intermittent Squeek Noise
Removed 2 screws from inside door lifted top panel up,removed 1 screw attaching front panel to left side. Pulled front panel out far enough to remove and replace slider bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Mocksville, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ddoor Handle Broken
Pulled broken one out and inserted new one in slots and popped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shauna from Bend, OR
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
High Squeaking noise
I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from Canastota, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic door handle broke off
super simple-snapped new handle right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Paoli, IN
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door handle
Snapped it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from haledon, NJ
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud squeak coming from dryer
remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Tyndall AFB, FL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dry squealed so loud you needed ear plugs!
The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Wilmington, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High Pitch Sqeaking durng dryer operation
Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Wenatchee, WA
- Parts Used:
- WE11M23
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer not getting hot
1) Disconnect power supply. 2) Open dryer door to find and remove two screws through dryer top. 3) Proceed to lift front dryer top panel and tap rear of dryer top with hand to left to disengage tabs and remove dryer top completely. 4) Remove two screws through front panel. 5) Gently lift dryer front panel from base tabs to partial remove panel (careful of wires which remain connected) - pivot front panel to left with wires connected. 6) lift dryer barrel with left hand / reach under barrel with right hand to release belt from tensioner pulley (very easy one-hand maneuver). pull dryer barrel belt off tensioner pulley towards you, remove belt from motor pulley below. 7) lift/pull and remove dryer barrel and belt (flex side panels). 8) take picture of wire connection locations on heating element and remove wires from tabs two locations / 3 wires. 9) remove sensors 3 locations. 10) remove heating element and housing. 11) install new heating element / housing and reverse process. .....tip; belt tensioner pulley was biggest challenge at first because it was hard to see how it all worked and reach. once i realized i could force / lift the barrel up to gain better access it was much easier than trying to fit my arm through the one large available hole at bottom right (when looking at the unit). the tensioner pulley is opposite side (left when facing) and you would have to reach over the exhaust, etc.
Was this instruction helpful to you?
Thank you for voting!