DDC4498AEL General Electric Dryer - Instructions

Pulled the top of dryer off. Separated the door from the drum seal or gasket, slipped the belt through, put the drive belt on the motor and then put it all back together.

open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

Started with removal of rear inspection plate on rear of drier,rotated drier drum by hand to look for any visible problems. Found that drive belt with age had lost sections of teeth and every time the bad sections would go past motor they would "thump".
1. Removed belt from tensioner. Done simply by moving tensioner to unload belt.
2. Slipped belt off motor drive and moved belt to front of drum.
3. Opened drier door and removed 4 screws from under the lid or top of drier ,raised lid for access to belt once belt had been slid to front of drum.
4. (steps 4 and 5 are the hardest parts)Worked drive belt between drum and felt insulators keep in mind there are many stamped steel pieces and sharp edges can be present.
5. Removed belt by feeding a small section past felt and drum and worked rest out from frt. top of drier.
6. Installed new belt in reverse order as removal.
This was done without aid of instruction manual and by someone having major back surgery 4 months earlier. No idea how much this saved me but the price of the belt and time and effort involved made it woth my while I'm sure.

Followed an online website, removed the top, front, two rear access panels, disassembled the spring clip from the rear of the drum, took the belt off of the motor, removed the drum, took the rear bearing support out, replaced the bearing and reassembled the dryer.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

2 part repair. I replaced the front drum slide kit in about 20 minutes. It was better but still made lots of noise (was quiet for about 20 minutes then started back) so I ordered the rear drum bearing kit & a new belt. Replaced them when parts arrived. The video was great (the instructions with the parts were poor). However, my model had a circlip holding the bearing to the mount in the heating element & the drum did not come out until I removed the 3 torx screws in the drum & the bearing remained attached to the heating element. The new bearing kit was the one shown in the video & it all went back together easily but the belt was impossible to get on from the front. My friend helped & we removed the back access panel (had to remove the dryer cord to get the panel off). Belt was easily fitted & thus far (1/2 hour of use so far) the dryer is quiet.

Removed the top, front and lower rear section of the dryer. This being my first experience replacing a dryer belt I naturally missed the tensioner pulley first try, then installed the belt on the wrong side of the pulley and found I didn't have enough tension. After some thought and a long hard look I realized my mistake and the third time was the charm. Next time I need to replace a dryer belt it should be a snap and go a lot faster.

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.

Checked out problem found belt broke and order part from part select and when it got in I replaced the belt and then found pully bad too. so I order that part from ya'll and it tok less than 5 mint to install. everything went very well and I and my wife are very happy with everything.
Thank's Partselect,
John& Roxanna

unplugged dryer,removed air duct,,remove( top of dryer) by removing the two back screws.... removed two screws under (fornt top lid),laid top to the side. ...Now remove ( front of dryer) remove,two screws near the( top on the inside)...lean dryer back, and remove outsidescrews at the bottom)..the front should come off. ..located small square opening in the back of the dryer release clamp from drum ,...put belt around drum... put drum and dryer back together...(relace any electrical wires removed if any..remove (rear bottom plug panel)..you can now see the lower inside of dryer....make sure belt is level on drum by rotating...place belt on lower pully,... lift tension(spring pully) on to belt.. replace cover..

nd removed it from the unit.
5. replaced drum bearings
6. reassembled everything in the same order I took it off.

Be sure to mark any wires you may disconnect to ensure you connect them back correctly.
Was a bit frustrating at times, but made it through and there is no more squeek.

After taking the dryer apart and not finding anything that looks like the one I have in this box that I ordered, I got the right part and dryer is working find.

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)