DSKS333EC3WW General Electric Dryer - Instructions

Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.

Took the dryer apart to get to the rear bearing. Took the bearing assembly out, kept the e-ring from the old bearing shaft, replaced the bearing kit, took the o-ring off the new shaft and replaced it with the e-ring, then reassembled the unit. Make sure to place a nail or long screw into into the rear of the drum, so that you can realign bearing on the drum. It is easier with two people when reassembling.

Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

Used online instructions. Worked well.

Easy! Just took the broken knob and metal ring off, and put on the new knob. took less that one minute. Works like a charm now. No service call cost either!!

Pilled and unsnapped the old two gaskets. Then I used my air compressor and blew out the excess accumulated lint. Then I snapped in place the new gaskets. The only trick is to be sure both sides of the tabs are anchored in and that is where the small screwdriver is carefully used to push one side or the other of the tab into the slot.

Just pulled off the old knob and pushed the new one onto the switch. Done in 1 minute.

First the old knob was broken just pulled it off. made sure the metal piece was clean of all debris or junk and slide the new know on turned it to make sure it was snug and was ready to go. to easy

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

replaced rear drum bearing kit Still makes the same noise

it was easy, it clip right on.needed to give it a little tap to get it in .

When I got the knob in the mail, I opened up the package, made sure the knob was identical to the broken one and pressed the new knob into place. I needed no tools to put the new knob on. It was easier than I thought.