DBSR453EB2WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- D J from Zwolle, LA
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Dryer on switch did not work
Ordered and replaced the starter switch. Ordering was easy, just entered the model # and got a diagram of the dryer, selected the started switch and place the order. The switch arrived a few days later. It was the right switch and installation was easy. Dryer is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Va Beach, VA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch stuck in the ON position
Followed other people's postings. This really is a simple at home repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Towaco, NJ
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not start due to defective switch
The biggest challenge was figuring out how to remove the defective starter switch. By searching the internet I found someone describing the same problem and that you had to turn in counter-clockwise to remove it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Hendersonville, TN
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking noise
Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruben from Odessa, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wouldn't turn off
Started out by unplugging appliance then pulled off knob, removed 4 screws that held cover in place, removed wires from switch, rotated switch to remove. reversed steps to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GUY from BEDFORD HILLS, NY
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum slide wore - damaged drum bearing
r/r parts unit runs great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Redondo Beach, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum wore down plastic
pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- derrick from gansevoort, NY
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer wouldn't run
very simple , unplug dryer and unhook the back of the top of dryer using a screwdriver on 6 screws. unhook clip to the rotary starter switch and unhook the three pronged plugs that go to the starter switch. replace new one that snaps into place, plug back in the three wires. screw the back of the dryer back on and your done. 6 minute job that saves you 40-50+ dollars for a repair man plus the extra money they mark up the parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Fort Mill, SC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would start when you closed the door during a cycle
All is necessary is remove 3 philip screws, remove the switch knob, lift a tab on the switch, rotate the switch counterclockwise and it was out. Pull wires off switch and immediately put them on the corresponding terminals of the new switch before reversing the above steps. Simple!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from swarthmore, PA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dryer would not turn on
Verified start switch was defective by jumping around switch to confirm the unit operated. replaced the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Williston, VT
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer squeaks and squeals while running
Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Lawrenceville, GA
- Parts Used:
- WE05X20431, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Very Loud Noise.
Took the front & top off the dryer. Saw that the slides were missing or broken. Got the parts and put it back together. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Sterling Heights, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn dryer drum slides
i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from santa maria, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
squeaking
snap in snap out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Wexford, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking sound from dryer drum.
Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.
Was this instruction helpful to you?
Thank you for voting!