DCSR473GT6WW General Electric Dryer - Instructions

put the new knob on and pushed it inward !! simple repair..PartSelect is a great company to do business with and very quick shipping, and great prices too. thank you so much.Brad S.

Knob fit perfect. Simple pull off and put new one on.

I used a pair of pliers to turn my dryer on until I broke the center part where the knob went. I order the part that was in the dryer first and it came the next day. When it got here I realized I still needed the knob. It came the next day also. It took my handyman about 15 minutes to replace both and he also cleaned out all of the missing socks and other items behind my dryer. Good Job!

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

TOO EASY to repair. WORKS GREAT>

Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....

After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.

I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.

I suspected and removed the timer to check it and found the timer knob had a crack in it and realized I did not know where it was pointing to. Checking the selector knob also showed a crack which prevented the dryer from starting.