DBSR453EB0WW General Electric Dryer - Instructions

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

Silmply replaced the knob. This is the second knob I have replaced on this dryer. This time I bought two for when it happens again. Not sure if it is too much rension in the timer or too little strength in the knob, but is a design problem.

The fact that the knob on a 3yr old dryer broke was harder to deal with than the repair. It was lift the old knob off (it was very loose) and snugly slide the new knob on. I can get back to reading my book and my wife thinks I'm a hero win-win!

Simply pulled off the old handle and snapped in the new one! No tools required. Took about 5 seconds!

Before ordering from PartSelect I had checked both the original vendor and a local repair shop. The vendor had nothing, said try online. The shop said they could order it for twice the price.

PartSelect sent exactly what I needed pronto. I pulled off the old knob. I pressed on the new knob.
Done.

The repair was pull old one off and replace new knob. Receiving the new knob was amazing. Ordered one afternoon and received new part by 11 am next morning at regular shipping. You can't ask for anything better than that. Thank you

Snap on part , order came in quickly and repair done unit good as new. .

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

just put new one on. no tools needed fits in holes already there. handle just snaps on,

This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.