DWSR483EA1WW General Electric Dryer - Instructions

Yes, we should have done this a long time ago and put off replacing the starter knob and heat adjuster knob. By the time they no longer worked, we called in an expensive repairman. When we realized what the problem was, we thanked him, paid him lots of money and did what we should have all along - replaced the knobs throug partsselect.com instead of using the repairman for another $150.00.

We received the knobs within 3 days (paying for medium fast delivery was worth it) and simply pulled the old problem knobs off and put the other ones on. Simple, no brainer work.

Save yourself expensive repairs and replace those knobs when they start going. Also, when you test the machine, make sure you turn the setting to a time (stupid mistake that most of us do) to make sure that the knobs work properly.

Good luck. A terrific experience with Partselect.com. Would use again in the future and recommend to others.

Worked Perfectly

The knob to start my dryer broke about a year age. I was using pliers to start the dryer. I was sure I would never find a replacement part and it was just a matter of time before the plier trick would break the start knob. I decided to look on line for a replacement knob sure that I wouldn't find one. Clicked on PartSelect, enter General Electric dryer and a bit more simple info and there was the part I needed. This site has everything. My dryer is good as new. Thanks PartSelect

Before I bought the new knobs, I put nail glue inside each knob to strengthen the knobs. It lasted for about 6 mos and I would have to do it again. Needless to say I got tired of the broken knobs, so I bought new ones.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

I thought that the timer was broken but when I pulled the knob off, there was a slight crack in it so before I contemplated calling a service person, I ordered a new knob. Now it works just fine and turns with the usual 'clicks' that I wasn't hearing since it broke. For the $20 ( including S&H ) It was worth the try. Thanks for the website, very easy to use!

I simply removed the switch and matched the pole numbers to the new switch eventhough the new switch had two extra poles. The switch replacement was straightforward and worked very well.

Took it out of the package. Slid in it in place, took less than two minutes.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

I suspected and removed the timer to check it and found the timer knob had a crack in it and realized I did not know where it was pointing to. Checking the selector knob also showed a crack which prevented the dryer from starting.

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.