DBL333GA0AA General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deborah from Yorktown, IN
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke the knob.
I used a pair of pliers to turn my dryer on until I broke the center part where the knob went. I order the part that was in the dryer first and it came the next day. When it got here I realized I still needed the knob. It came the next day also. It took my handyman about 15 minutes to replace both and he also cleaned out all of the missing socks and other items behind my dryer. Good Job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Marietta, OH
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Start switch broke
Followed the on line instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Staten Island, NY
- Parts Used:
- WE12X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the dryer belt broke
very simple my husband put it on in no time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from perrysburg, OH
- Parts Used:
- WE4X750
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No heat
The wife complained of clothes not drying. Ordered a igniter without checking for exact cause to save time. When I was able to I took the top and front panels off. Unfortunately the igniter was fine. I ruled out the limits and igniter with a VOM meter. I quickly ordered the gas valve solenoids. After a quick delivery they were replaced with a screw driver and panels replaced. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Port Charlotte, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
It was only a matter of putting a new knob in place of the broken one. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bakersfield, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer Start knob broken inside of stem.
Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.
Was this instruction helpful to you?
Thank you for voting!
Selector Knob and rotary switch broken
Unplugged dryer and pulled away from wall a sufficient distance to be able to stand behind it. Located the four screws located along to top of the dryer control panel. Selected the correct torx bit (not philips or slot) and unscrewed all 4 screws. Front of control panel rotated open such that the inside of the rotary start switch was visible. Removed broken switch by pushing down the catch tab with one finger and using the other hand to rotate the switch counter-clockwise about 1/4 turn (to the 9 o'clock position). Installed new switch by inserting in the same 9 o'clock position and rotating clockwise until the metal tab locked the stitch in place. Used a vacuum to clean out lint and replaced panel and securing with the 4 screws. Attached the new selector know by lining up with hole and pushing in. Took the extra 2 minutes unscrew the band holding the air vent and vacuum the lint out. Replaced the flexible vent by tightening the band. Carefully pushed back the dryer, ensuring not to kink the flexible vent. Plugged dryer back in. Worked like a champ.
Was this instruction helpful to you?
Thank you for voting!