BWXR473EV0AA General Electric Dryer - Instructions

I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.

I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.

Took the dryer apart in an adjacent unused bedroom. Saw that the element was bad. Ordered new part from Part Select and installed when it arrived. The whole situation went as smooth as could be.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

Before removing the old part,took photo with my phone camera to document the color wires hook up. Screwed in the new part and hooked up the color coded wires using the photo as reference. I was surprised how easy it was. Thanks. Partselect gave me fast shipping, cheap price and great customer service.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

Removing the old door was the problem as the old screws were rusty. Then, because we are not very spatially adept, we had trouble putting the door back together with correct hinge alignment. This should have taken about an hour and the part was perfect. The dryer, which we were going to throw away, looks and works perfectly! Parts Select offers great, timely service.

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.

My dryer would run but not heat and the timer would not advance. PartSelect helped me determine that the heating element needed to be replaced. I have very little experience with appliance repair. I found this to be challenging but well worth it.

TOO EASY to repair. WORKS GREAT>

Had to remove the drum to get at the heater element also had to swop the sensers to the new element

Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....

1) Disconnect power supply. 2) Open dryer door to find and remove two screws through dryer top. 3) Proceed to lift front dryer top panel and tap rear of dryer top with hand to left to disengage tabs and remove dryer top completely. 4) Remove two screws through front panel. 5) Gently lift dryer front panel from base tabs to partial remove panel (careful of wires which remain connected) - pivot front panel to left with wires connected. 6) lift dryer barrel with left hand / reach under barrel with right hand to release belt from tensioner pulley (very easy one-hand maneuver). pull dryer barrel belt off tensioner pulley towards you, remove belt from motor pulley below. 7) lift/pull and remove dryer barrel and belt (flex side panels). 8) take picture of wire connection locations on heating element and remove wires from tabs two locations / 3 wires. 9) remove sensors 3 locations. 10) remove heating element and housing. 11) install new heating element / housing and reverse process. .....tip; belt tensioner pulley was biggest challenge at first because it was hard to see how it all worked and reach. once i realized i could force / lift the barrel up to gain better access it was much easier than trying to fit my arm through the one large available hole at bottom right (when looking at the unit). the tensioner pulley is opposite side (left when facing) and you would have to reach over the exhaust, etc.