DBSR453EB1CC General Electric Dryer - Instructions

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

snap in snap out

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

r/r parts unit runs great

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

I simply removed the switch and matched the pole numbers to the new switch eventhough the new switch had two extra poles. The switch replacement was straightforward and worked very well.

TOO EASY to repair. WORKS GREAT>

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.

It was as easy as the repair film said it was . But after spending the money for the upper and lower baring seals I put it all back together and the motor started making a loud noise ? I took the drum and everything out and started the motor without the drum just the motor was running and the danged motor is going out now !I checked the price of a new motor its not to bad but with all of the parts I have put in this thing I could have paid part of what it would have cost for a new dryer ! I put it all back together and hope it last long enough to at least recoup some of what I have spent ,But the new parts work good !

1) Disconnect power supply. 2) Open dryer door to find and remove two screws through dryer top. 3) Proceed to lift front dryer top panel and tap rear of dryer top with hand to left to disengage tabs and remove dryer top completely. 4) Remove two screws through front panel. 5) Gently lift dryer front panel from base tabs to partial remove panel (careful of wires which remain connected) - pivot front panel to left with wires connected. 6) lift dryer barrel with left hand / reach under barrel with right hand to release belt from tensioner pulley (very easy one-hand maneuver). pull dryer barrel belt off tensioner pulley towards you, remove belt from motor pulley below. 7) lift/pull and remove dryer barrel and belt (flex side panels). 8) take picture of wire connection locations on heating element and remove wires from tabs two locations / 3 wires. 9) remove sensors 3 locations. 10) remove heating element and housing. 11) install new heating element / housing and reverse process. .....tip; belt tensioner pulley was biggest challenge at first because it was hard to see how it all worked and reach. once i realized i could force / lift the barrel up to gain better access it was much easier than trying to fit my arm through the one large available hole at bottom right (when looking at the unit). the tensioner pulley is opposite side (left when facing) and you would have to reach over the exhaust, etc.

Unplug dryer, unscrew bulb then replace with a new bulb. Plug dryer back in.