DDE7900SBLWW General Electric Dryer - Instructions

It took more time to figure out how to get the dryer apart than it did to fix it. Unfortunately I ordered the wrong parts the first time but Part Select was very helpful and efficient in helping me get the correct parts. I located the two screws that hold the top onto the machine inside the door frame at the top. Once the top was off, there were two screws that held the front door assembly to the dryer. The old parts (very worn and next to totally gone = none of the slides were remaining) were easy to snap out and the new parts easy to snap in to place. The Spa is happy that the dryer is quiet again and can be run when we have clients waiting. Thanks to you Part Select.

When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

Ok so it finally died. Breakdown is relatively easy. UNPLUG the dryer before doing anything else. Remove the dryer vent plastic hose from the dryer--replace if torn. Remove the screws from the back plate covering the switches. Go to the front of the dryer--open door and locate 2 screws at about 11 and 12 o'clock. After removing these 2 screws you should be able to lift the top off the dryer. Take note of the wiring connections--I took a picture of the wiring from my cellphone just in case. Go behind the dryer and locate the access to the electric motor to remove the belt that spins the drum. There is a wheel/belt tensioner--remove the tension from the belt. You are now ready to lift the drum out. While you have this drum out, now is a good time to vacuum all the lint out. Once the drum is out, you'll see the heating element. If the wiring element is broke, just replace the wiring kit not the entire assemby (save $100). While you're at it replace the high limit and safety thermostats (about $28 for both) very easy to replace--unscrew and just replug the wires back to the original terminal locations. To replace the Timer/heat selector, remove a screw that holds the assembly and plug the wires back per your diagram or better if you took a picture from your cellphone. Assemble in reverse direction. Good luck!

Belt and pulley both broke. Ordered parts; received 2 days later. Took off front and top, positioned belt, replaced pulley and nut. Parts fit perfectly. Reinstalled covers. Ran dryer. Easy fix.

I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.

Remove old one, put the new one in!

I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

Pulled off old knob put on new one

The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

my two twin boys Mike and Curtis age 14 did the repare they toke of the front of the dryer then the top put the belt around the drum then put the top and front back on then went to the back and removed the panel and put the belt on the pulley then set the tension wheel then put the back cover back on
the repair was easy I watched to make sure they did it right and did not have to tell them how I am very proud of them they do great work
finding the part was easy and it was here the next day after I ordered it and it was only sent 3 to 5 work days. You guys have a great web site and fast shipping thanks for the good work!

Removed the broken handle from the dryer and popped on the new one.

I opened the vent system (screwdrivers to loosen screws) and used the shopvac hose and my hands to clean out what I could. I also snaked the shopvac hose down into the dryer and removed clogged lint. Then I just replaced the lint filter.

Easy as 1-2-3. I took off the top hinge screws in order to lift up the top of the dryer.

I then took off the front dryer piece with the door intact. The lint filter was in the front door section.

I released the wiring clips to the front of the dryer and lowered the front of the dryer down gently. there is enough slack with the wiring if you disconnect the wirre clips.

I removed the old broken belt. ThenI gently lifted thr dryer drum enough to slid in the new belt with the ridges down. Look for the old belt line (worn area on the drum) and slip the belt up on the drum to that point.

Then I replaced the wiring with clips and put the front of the dryer back together.

Going around to the lower back of the dryer, I unscrewed the back plate where the exhaust comes out. It was 8 screws with a socket.

Once the back was off, I pulled the dryer pully to the right and fed the reamider of the belt through both pulleys ensuring that the ridged side was on the correct side of the pulley. The pylleys match the ridges on the belt. I rleased the tension on the movavle pulley and it was done.

All I had to do was button the back up and do a "dry run" I quick have the drum a half roation from inside the drum with the door open. Then it was all gravy. I was done and saved myself a good deal of money. Look on the net for pics to make thing easier for you. There are people out ther who will NOT charge you for this info.

First i removed the lower rear inspection plate to see what the problem was.
next i removed the screws in the front top panel.
next i lift the top back,the rear hinges held it in place.
next i removed the bolts that held the front panel in place,but before i removed the panel i removed the wires that were connected to the front elements and disconnected then,
next i removed the front panel,then i place the new dryer belt over the dryer drum,but first you have to rise the drum up a little to get the belt under it.
next i put all the front panels back in place,make sure you reconnect the wires that you removed earlier.
next i moved to the back panel, there i position the belt over the dryer drum,then i place the belt over the motor drive pulley, then i pull down the tension bar roller to the left and place the belt over it.Then i replace the rear panel in place.plug in the power core and turn it on. finished. After over 35 years this is the first time i had to replace the belt,matter of fact this is the first time i had to replace anything on this dryer, washers will that is a different story. but the dryer runs great maybe for another 30 +years LOL.