DNCJ440EA0WC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dorothy from Flushing, MI
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom clip on handle broke off
Removed handle from box...walked into the laundry room...snapped part into the door panel. All done! Thanks for the prompt delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from Oakdale, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
handle on dryer door broke
It was really easy to find the correct part. It was shipped right away and fit perfectly when it got here. Very satisfied with the whole process. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from Verona, NJ
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door handle
Very easy to install, snaps right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Rochester, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle on dryer
The part was shipped quickly and I received it within the week. I was afraid that because it is an older dryer the new handle would not be compatible, but it was! It installed easily, it only took a few seconds to clip it in and now it's as good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Thayer, MO
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broke
new handle just popped right in the slots
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from Canastota, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic door handle broke off
super simple-snapped new handle right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Paoli, IN
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door handle
Snapped it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from spokane valley, WA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
grinding noise -- sudden onset
I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Richmond, VA
- Parts Used:
- WE4M415
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer would not turn on
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nate from Affton, MO
- Parts Used:
- WE11M23
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Dryer runs but does not heat
My dryer would run but not heat and the timer would not advance. PartSelect helped me determine that the heating element needed to be replaced. I have very little experience with appliance repair. I found this to be challenging but well worth it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Wilmington, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High Pitch Sqeaking durng dryer operation
Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Mansfield, MA
- Parts Used:
- WE11M23
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dryer was not heating up
Had to remove the drum to get at the heater element also had to swop the sensers to the new element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Cumming, GA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from haledon, NJ
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud squeak coming from dryer
remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Summerdale, PA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would run for 4 minutes and shut off. keep turning it on
Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.
Was this instruction helpful to you?
Thank you for voting!