DPSQ475GT2WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Garrettsville, OH
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum wobbling and thumping
Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Genoa, IL
- Parts Used:
- WE4M181
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would get hot and shut off.
Turned off gas and unplugged power. Removed gas line and vent tube. Removed the light bulb. Took the door off. Removed two screws from the top, inside part of the door jamb and removed the top, but not the control panel. Removed the front panel. I took a picture of the wiring that leads to the light to ensure proper reconnection. Unhooked the belt from the tension bar and removed the belt, then pulled the drum out. The cycling thermostat is held in place by 2 "wings" and pressure. Removed connections from old and installed on the new. Snapped the new cycling thermostat in place. Then reversed the order to reinstall everything. Drum, belt around drum then tensioner, connected light wiring, installed the front panel, ensuring proper alignment on the felt in the lower bearing. Installed the top and screwed it back on the front panel. Reinstalled door. Reinstalled the light bulb. Using NEW gas line plumbers tape, installed the gas hose. Installed the vent tube. Have done at least 10 loads of laundry with no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAMCHANDAR from BRISTOW, VA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
noisey
TOO EASY to repair. WORKS GREAT>
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Wilmington, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High Pitch Sqeaking durng dryer operation
Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from haledon, NJ
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud squeak coming from dryer
remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Huntington Beach, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer squeaking/squealing sound
After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Oakville, IN
- Parts Used:
- WE4M181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dryer was not heating up
We watched the video of how to take the dryer apart and how to install the thermostat...after watching the video it was pretty easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from shirley, NY
- Parts Used:
- WE25X217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
dryer never converted from natural to propane gas
followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Marblehead, MA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The time knob had broken and come off
Our repair was super easy. All we had to do was line the new Timer Knob up with the knob on the dryer and slip it on. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from San Saba, TX
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer would not turn on
took the old part off @ put the new one on. Took about 5 sec.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Stockton, CA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken timer knob
Knob fit perfect. Simple pull off and put new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from hertford, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Loud Squealling noise from dryer
Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Knoxville, TN
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer Knob - Stripped
Parts arrived and it took me less than 5 minutes to get the packaging open and install the knew timer knob. I had ordered a separate D-ring; however, one was already present in the timer knob so now I have an extra.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyle from Edisto Beach, SC
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bad timer knob
just pushed it on . This was one of the most pleasant internet ordering experiences I have ever had. Glad I found you. Thanks Doyle Weeks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Dewitt, IA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer knob, plastic broke, could not turn on.
pulled old one off, pushed new one on!
Was this instruction helpful to you?
Thank you for voting!