DWSR483GB0CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Enterprise, AL
- Parts Used:
- WE1M462
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
With the help of doityourself guy on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from HOPKINS, MI
- Parts Used:
- WE14X25080
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
a lot
started with replacing the belt and tension pulley which I purchased from another source. I found your videos on line and they are great. easy to follow. Realized I needed the bottom vent assembly and your prices were better than my local supplier. It was easy to replace thanks to your video. It was nice that you included it in the final order status. The only problems. Did not know the duct felt seal was included with the new duct assembly. I ordered the wrong bearing slides, web site showed both green and white for my model. I now realize I should replace the upper bearing housing. Can I return the unused parts, unopened and have that put as a credit to my next order? Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from GALES FERRY, CT
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken piece
Snap out the broken part. Snap in the new part. Use caution with the wires, but don’t have to disconnect them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Simpsonville, SC
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rubbing noise while dryer was running
Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Albuquerque, NM
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was making a loud squealing noise.
I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Forrest from Mays Landing, NJ
- Parts Used:
- WE14X25080
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked air duct
Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ELVASTON, IL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
On knob went bad
Took new one out of package, and push it on. 4 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from MONROEVILLE, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken start knob
Just push knob on less than 4 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BALTIMORE, MD
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking
Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarke from Grapevine, TX
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeek when dryer was running
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MONROE TOWNSHIP, NJ
- Parts Used:
- WE01X20580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broke to dr;yer
handle broke on sunday( not the best day to order things). ordered it from this site and had it by tuesday. great service and best price i found on the web. tks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from SCOTTSDALE, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My dryer wouldn't start, I saw the part on your website after reading comments from other people
I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from MANHATTAN, KS
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Start knob broke off
At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from YARDLEY, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob and could not turn on dryer
followed the video you provided and it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Deerfield, IL
- Parts Used:
- WE14X215
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
No heat from dryer. Diagnosed by others as the Gas Valve
Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.
Was this instruction helpful to you?
Thank you for voting!